Airspeed and Throttle handling clearifications
@Remi wrote: Hi!I have a few questions regarding how the throttle and airspeed is handled in the different flight modes.Important info: I am using a airspeed sensor. I see that in FBWB, the throttle...
View ArticleClik here to view.
MNT_STAB_ROLL enable cause board refuse working when tilting
@Cipta wrote: Copter-3.5 Testing List MNT_STAB_ROLL enable cause board refuse working when tilting [image] RC11 - Gimbal tilt - SERVO5_FUNCTION,7 RC12 - Gimbal roll - SERVO7_FUNCTION,8 SERVO7_MAX,1970...
View ArticleCoter current limiting
@kuspower wrote: Hello, Someone can explain how work current limiting in AC3.4.4 ?MOT_CURR_MAX ? In copter wiki:This protection automatically drops the throttle to as low as 60% of full throttle in...
View ArticleAutolanding Turn after flare
@wbal57 wrote: Hi, I am running arduplane 3.7 with an airplane that is rudder only. It has a lidar lite sensor installed with the hope of using the lidar for autolandings. We have made two auto...
View ArticlePixhawk autopilot for custom UAV
@lukashou wrote: Hi everyone, I'm quite new in DIY UAV stuff, so I have a ton of question and hope you'll help me to figure out something. I would like to create a drone (with Pixhawk autopilot) with...
View ArticleClik here to view.
MP 1.3.43 and 1.3.44 don't connect to Dragonlink v3 Tx using Bluetooth
@ultrafuge wrote: Hi, I can connect to Dragonlink v3 Tx using Android Tower using tablet or mobile without a problem.Two different W10 laptops can pair via Bluetooth to Dragonlink v3 Tx, but 90% of...
View ArticlePixhawk px4 Esc compatibility
@Andrea_Ercolino wrote: Hi everyone, my name is Andrea, passionate about quadcopters and electronics.I am about to start my first project with Pixhawk px4, however I was reading on different forums of...
View ArticleLanding Detection Logic Doesn't Work for High Powered Copter with KDE Motors
@rrr6399 wrote: We have copter with that require these settings due to using KDE motors:MOT_SPIN_ARM=.22MOT_SPIN_MIN=.225MOT_THST_HOVER=.33 (from the auto hover learning process) But, the logic in...
View ArticleReview a log - map
@JeyPi wrote: When we review a log, it is possible to see the map in the log browser.I was not able to locate the documentation on the map.There is a blue line and a red line of the flown track. What...
View ArticleArduRover 3.1.1 Arming Issue
@RayN wrote: I currently have a Pixhawk installed on an Actobotics Nomad. I uploaded the Rover firmware (v3.1.1) through Mission Planner. I enabled Skid Steering through the Basic Parameters Tab. I am...
View ArticleDEV call 13 Feb 2017 3pm PST = 13 Feb 2017 2300 UTC
@CraigElder wrote: Copter Intel Aero RTF update Plane Tailsitter work Prop hanging Soaring patches Sub progress on sub merge Rover Antenna Tracker Hardware CAN update Posts: 1 Participants: 1 Read...
View ArticleUnable to unzip async-TX1
@rbachtell wrote: I have tried to unzip the download with every method I have been able to come up with on both a Mac and Ubuntu (14.04 and 16.04). Tried several unarchive tools on both platforms and...
View ArticleWhere is my quad icon on map?
@Ertu_Kocak wrote: Hi I usually see my quad icon on map when is tart mission planner.But last try, is just disappear .. Have tried to unistall an install again but no luck.Have tried different version...
View ArticleClik here to view.
Too many vibrations
@Ertu_Kocak wrote: Hi Upair V3, 1.0.0.2 - arducopter firmware 3.2.1I need your help When i take off my quad seems to move erraticclimb 10m, fall 2m, go left 1m, right 2m etc ... Here is the log i get...
View ArticleErr: 24-1 and 24-0 while flying at high speed with RTK GPS
@Stijn_Debecker wrote: I'm getting a lot of 24-1 and 24-0 errors while flying at high speeds (25m/s) :demo_26.zip (3.2 MB) Is it possible that these errors are related to the SP-ratio from the...
View ArticleRover 3.1.1 Throttle with Pixracer
@dkemxr wrote: Has Pixracer been confirmed working with Rover 3.1.1? I cannot seem to get a throttle signal out. It Arms (all checks off) but nothing out (ESC doesn't initialize). Steering (channel 1)...
View ArticleQuadrocopter rotate in yaw axis
@SNEIJDERPL wrote: Helo,i have another problem with my quadro.When i want to start, copter always turn his position in Yaw axis(left side).This is my Log from first start. Please tell me, this is not...
View ArticleConfigurations of pin as input/output
@Andre wrote: I need to use 2 the auxiliary pins of Pixhawk as digital output, and 2 as digital input, so I would like to know how configure it. The parameters I set are: BRD_PWM_COUNT = 0 RELAY_PIN =...
View Article3DR Radio in Bootloader mode after failed firmware update
@rrr6399 wrote: I was testing out qgroundcontrol GCS and it managed to automatically try to upload firmware to my 3DR radio without my permission. I wasn't able to connect to my radio and discovered...
View ArticleRunning AP Version on RPI (like Aero)
@mgrindle wrote: I was lurking on the Dev Call this week (13 Feb 2017) and have a question. Has anyone attempted to do what Lucas dM is doing with the Intel Aero and AP but instead using a Raspberry...
View Article