Clik here to view.
Weird problem with i2c splitter and external LED
@davyg wrote: Have built up my hexa and added the I2C splitter to it, all is working A.OK so far now for the problem..... The external LED works grand , but won't work period when the GPS puck is...
View ArticleMP .msi Install skipping Driver Install
@Autonomost wrote: I am installing Mission Planner and for some reason it skips the driver install entirely. I am used to the warning popping up for the drivers but this time it skips it entirely....
View ArticleUpdate firmware using TELEM1 / SERIAL1 port on Pixhawk
@jeroent wrote: I have tried to do a firmware update using the TELEM1 port, but it fails. Does the bootloader actually support updating of the firmware using a UART? Posts: 1 Participants: 1 Read full...
View ArticleCant compile 3.3 for APM 2.6
@Jo_Ho wrote: Hi,I was finaly able to Compile Copter 3.2.1 on Linux with the makefile.But now I want to Compile 3.3 and it sais it cant be compiled for APM2 but in missionplanner I can download and...
View ArticleQuadplane landing issue using weathervaning, Quad hover and forward motor...
@JeffBloggs wrote: I think there might a potential problem with the current quadplane code using both quad and forward motor at the same time whilst in position hold and trying to land. The issue can...
View ArticleBatteries , Li-ion vs Li-Po Which better? why?
@ahmed wrote: Hi all , Most rc fliers use Li-po batteries , But when I use it I just get fly about 10 min then battery off and need throttle again - seems to became hot - When I use Li-ion batteries I...
View ArticleHow To Obtain 0 Degree Neutral Gimbal Tilt
@davidbitton wrote: I have channel 6 controlling tilt on my STorM32 gimbal over Mavlink using RC Targeting mode; channel 6 is tied to the righthand slider on my Taranis. The min and max PWM are 1000...
View ArticleGeo Fencing for Rover?
@ColinHurd wrote: Grant, Any update on the geo fence for rover capabilities? Ideally it would allow for a polygon geo fence. I think the obstacle detection/avoidance feature would be very useful as...
View ArticleAPM 2.6 Sonar mounting
@laser_nerd wrote: Should I mount the sonar unit rigid or isolated is my question? Posts: 1 Participants: 1 Read full topic
View ArticleTelem 2 conflict with offboard control
@jasonbeach wrote: Hi, I'm setting up a pixhawk (genuine 3DR) running Copter 3.3.3 to accept commands from an external Linux computer (Jetson TK1). The two are currently connected via USB on the TK1...
View ArticlePixhawk not echanging informations by bluetooth
@st-camille wrote: Hello, I just bought a "Bluetooth Data Link Modul zu Pixhawk PIX 2.43 " for my pixhawk and I tried to connect it with Windows and Android but it didn't work. The red light on the...
View ArticleWhere are pins A0~13?
@Arif_Rahman wrote: Hello all, I want to read a 0 - 3.3V signal, so I am trying to use the 2nd battery / BATT2 voltage sensing pin. I found the following parameter definition in the documentation;...
View ArticleCommand heading or auto heading?
@rsjsrc wrote: I was wondering if it is possible to give a heading command via mission planner and have the rover go in a straight line at that constant heading. I do not want to do a waypoint...
View ArticleQuad is unstable in GPS only and switches unexpected to failsafe and land mode
@Tam_Amaruk wrote: Hi there, I got a APM 2.6 flashed with latest copter firmware. When not in any GPS-envolved mode everything is just fine.But when I activate any mode that uses GPS (e.g. PosHold)...
View ArticleSITL connection problem (MavProxy, Mission Planner)
@copter_pro wrote: Hi, I successfully launch SITL, even managed to control it via Android tablet.However, I fail to connect to it via local app like MavProxy or MissionPlanner. In MavProxy I enter...
View ArticleCreating offsets to do Swarm functionality in Dronekit via Python
@paan2097 wrote: I am trying to create a python script that runs in DroneKit to mimic the functionality of Swarm in Mission Planner so the UAVs can maintain formation and offsets even if they lose...
View ArticleNewbie need help building pixhawk code
@dlopez wrote: i just cloned the ardupilot project and I'm trying to compile using make command. It runs for a while then errors out; not sure if I'm missing something. My first instinct tells me a...
View ArticleMAVLINK Common Message Set in HTML link not working
@MajorPuddin wrote: I am currently unable to connect to the MAVLINK Common Message Set: (Protocol Definition).https://pixhawk.ethz.ch/mavlink/ Is anyone else having the same issue? Posts: 1...
View ArticleArduRover: Using more servos in both Auto and Manual mode
@kiki0000 wrote: Hi.I am building an ardupilot apm2.6 controlled RC boat and I would like to use two additional servos for releasing things in both Auto and Manual mode with a 6 channel transmitter....
View ArticleRTK Integer Fix / Float not recognised by AC3.4.1 using NMEA protocol
@kuspower wrote: Hello, I'm using NAVSPARK RTK 2 NS-HP-5 modules. RTK Fix is working well and we check status using wifi and NavSpark software. But mission planner only mark DGPS when float or fix,...
View Article