How to use logfile/tfiles
@jwcalvert wrote: Is there documentation somewhere?I have scoured for it but with no luck. Cheers Posts: 4 Participants: 2 Read full topic
View ArticleFuse bits for APM 2.5
@niranjan wrote: hai guys, i had started my own project to build APM2.5 for my project, from scratch. can some one halp me what are the fuse bits values for ATMEGA2560 and ATMEGA32u2.... please...!!...
View ArticleAssisted hand launching
@Rusty_Jones wrote: OK, I know ArduPlane can do auto take off, but I think you have to set a TAKEOFF waypoint, correct? Can ArduPlane assist in a hand launch of a fixed wing (Bixler 2) so that when I...
View ArticleWaypoints relative to home
@wicked1 wrote: I'm wanting to plan some missions where the copters goes up, and fly's a specific pattern, regardless of its location.So, the waypoints would have to be based on home position.. LIke,...
View ArticleClik here to view.
MP hanges upon converting to " .Log" after Mavlink download
@JoeBreznai wrote: Having a problem when downloading a large log into MP. Both current version and Beta . Log will download. then MP hangs upon conversion to ".log" format near the end of the process....
View ArticleTrouble doing parameter reset
@paan2097 wrote: I am following these instructions:Option #2: Change the SYSID_SW_MREV parameterOn any Ground Control Station (that can write parameters) you can reset parameters by setting the...
View ArticleCommunication between companion computers
@paan2097 wrote: I want to set up a network between multiple companion computers to allow UAVs flying in a swarm formation communication so position and velocities can be more linked up and a closer...
View ArticleHow to change the code of the pixhawk to make it fly automatically
@Shurr wrote: Hi, We are trying to change part of the code of the pixhawk, but it seems out of our ablity. So, is here someone who could help us? Posts: 1 Participants: 1 Read full topic
View ArticleAPM 3.1 with motor shield
@Pilot2016 wrote: Hi I am new to Ardurover. I have APM 3.1 and have worked on Arduino and also CC3D in a quadcopter. I want to know how to use APM 3.1 in autonomous mode to run motors using motor...
View ArticleClik here to view.
Error " EXP 81 GOT A1 AT 236653 " during install of APM 2.6 version 3.2.1
@jeraldthompson wrote: Noobie here - 1st post Whirlwing 550-type hexacopter with a Turnigy TG-9X transmitter, Turnigy receiver, Arducopter Flight Controller, CJMCU-GPS, Turnigy 28-265 1200 kv...
View ArticleHow to set ek2 to use optflow as failback when gps fail occurs
@kuspower wrote: @ Randy Hello, I remember that on diydrones copter ac3.4 rc1 topic Randy explained that ek2 is able to use optflow if gps fail fail occurs. I would like to test this feature, could...
View ArticleCan't arm my rover
@wjwj wrote: hi all, i am using a pixhawk apm with a 3dr gps/compass. everything is fine except that i could not arm it with my controller. the only way i could arm it is from my mission planner. how...
View ArticleCrash Analysis Help
@drubug wrote: Hi All, Been a few years since I used ArduCopter and the Log files have moved a long way since I last used them Hoping someone can check my theory about crash on 2nd flight of new quad....
View ArticleMotor Control code a mystery
@jwcalvert wrote: Version 3.0 of CodePixhawkTrex Motor ControlIer on 6WD Thumper Now running fairly well in both Manual and Auto.But turns are very laboured so I need to tune these. To that end I have...
View ArticleAutotune is divergent in pitch. 'Copter screws itself into the ground
@Hugh_Neve wrote: Hi, I have what used to be a Quanum Nova / CX-20 with a genuine APM running firmware 3.2.1. The Autotune mode is set up to a combination of switches. In Autotune a sequence of moving...
View ArticleIs it possible to program a 3dr Solo drone to search in a low altitude (1.5...
@ricitron wrote: I'm working on a drone project and we are trying to see if it is possible to program a 3dr Solo drone to do the following: Fly in an automated grid search pattern at a specified...
View ArticleClik here to view.
Mavlink controlled alexmos gimbal moves yaw in wrong direction
@Tom_Gear wrote: Hi, I got a problem with my alexmos gimbal. Communication between gimbal and pixhawk works fine. But if I try to test the funktion like it's written in the wiki "Testing the gimbal...
View ArticleCan I buy the Solo 3DR drone and use the Copter firmware?
@atzmongh wrote: I am new to this site and to the world of drones. I am interested in the software side of the drones.So I want to understand if I can buy the ready-to-fly Solo from 3DR and replace...
View ArticleUpdated from 3.2.1 flight mode selection and another problem rears it's ugly...
@davyg wrote: I foolishly updated my 3DR Pixhawk to the latest firmware (not Beta), and afterwards I was left scratching my head and pulling out what little hair I have left...the problem is this.......
View ArticleUnable to set the servo configuration, Help needed
@Maaz wrote: Hello, I am using Pixhawk autopilot on a Raptor G4, fuel powered, Flybar system. The problem that i am facing is that i connected the servos in the "main out" of the servo rail in the...
View Article