Clik here to view.
QuadPlane Conversion of Hobby King Bix3 Trainer
@GregCovey wrote: Hi, This is my first QuadPlane project so I decided to keep it simple and small as a test bed for future larger conversions. I have many multi-rotor copters and planes but only two...
View ArticleSafeTrim does not adjust the Param AHRS_TRIM_X or _Y
@lorbass wrote: After the procedure showed here: http://ardupilot.org/copter/docs/autotrim.html?highlight=autotrim(Channel 7 switch above 1800, after landing, throttle Zero for at least 1sec, still...
View ArticleLightware SF11/C appears to stop working with 3.4 rc1
@Lance_B wrote: Like the subject says. I've got several different ways of providing stable 5vdc so it's not a voltage issue. Tried 5vd from power module, bec, from the serial port, from the i2c port...
View ArticleWhich RTKGPS to try with a rover?
@Tractor_Pilot wrote: Hello, I have built a rover using an APM 2.7, Sabretooth 2x32 speed controller, 12V brushed motors. This youtube video gives a quick demonstration of what it is. It still needs a...
View ArticleClik here to view.
Governability Bad Proble APM 3.1
@Phoedus wrote: Good morning;I have a really bad problem on my Emax Nighthawk 250; I describe what happens every time flight: mode : stabilized ; It makes a very stable and slow flight , after a few...
View ArticleAPMRover2 v3.1.0
@gmorph wrote: Any problems/questions/issues specifically related to the Rover 3.1.0 release please post them in here. Posts: 1 Participants: 1 Read full topic
View ArticleAbout the Rover 3.1.0 category
@gmorph wrote: (Replace this first paragraph with a brief description of your new category. This guidance will appear in the category selection area, so try to keep it below 200 characters. Until you...
View ArticleRover 3.1.0 BETA
@gmorph wrote: Hi everyone. The ArduPilot team is proud to announce the Rover 3.1.0 BETA. This BETA release is for users who want to try out the latest and greatest new features. In this release the...
View ArticlePlanning waypoints and RTL? Headache
@PSYCHICS123 wrote: Ok, so I have set up RTL on my turnigy 9x (so when it looses signal or my rc remote turns off the receiver will transmit (Failsafe) RTL. When I am planning mission planner with...
View ArticleClik here to view.
MP hangs during accelerometer calibration
@wkf94025 wrote: Michael, I am bringing up latest ArduPlane 3.6 with latest MP 1.3.39 on a PixFalcon for use in a motor glider. All is going well except accelerometer calibration. In the attached...
View ArticleLoiter toilet bowl flyaway, HK Pilot 32
@robotevan wrote: For the past couple months my quadcopter has been having compass heading problems. Before I updated to arducopter v.3.3.3, the quadcopter was able to maintain its position and alt in...
View ArticleAPM 2.6 sonar not working
@nitin0836 wrote: i have apm 2.6 with quadcopter configuration .. it flies perfectly. but i wanted to add sonar to it for better altitude hold capabilities.. i have made the connections all right and...
View ArticleClik here to view.
Problems getting Rx Failsafe to trigger RTL
@wkf94025 wrote: I am bringing up ArduPlane 3.6 latest on PixFalcon, using Mission Planner latest. Radio is Futaba 14SG and Rx is R7008SB. Radio and Rx have good failsafe programming abilities, and I...
View ArticleMinimOSD updating gps, voltage and current
@Vorona wrote: Hi all!Early I wrote about problem with update params in OSD on firmware extra-2.4-r800: http://discuss.ardupilot.org/t/apm-osd-battarey-info-and-gps-update-problem/7404But nobody has...
View ArticleClik here to view.
Uncommanded yaw
@tabascoz wrote: Hello All, Today I have experienced an uncommanded yaw. I was flying with my hexa ( very stable setup, more than 100 flights ). It was very windy, i was going towards the wind, when I...
View ArticleDoes AUTO mode prioritize horizontal positioning before increasing altitude?
@frizensami wrote: Hey all, In a project i'm involved with, an X-frame octorotor with Copter 3.3 executes a mission containing1) Takeoff to 8 meters (Lat = 0, Lon = 0)2) Loiter at 8 meters for 5...
View ArticleCompilation error in uORB module
@Jeffson_Wu wrote: Hi, I am new to ardupilot,after I compiled the arducopter using make px4-v2, this error happened : %% MODULE_MK =...
View ArticleCalibrated ESC changes in ardupilot
@john wrote: Ardupilot apm2.8 setup everything in missionplanner except esc since won't update to 3.3. Therefore I calibrated each ESC separately with the receiver. Each one worked as it should....
View ArticleChanging between auto and guided mode
@Yeo_Wei_Sheng wrote: I would like to ask if it is possible to plan out a waypoint mission and in between the mission have the copter to go out into guided mode for a while then return later to...
View ArticlePixhawk twitchy YAW and not disarm on crash
@jawood wrote: Hi everyone, hoping someone can help me with my pixhawk problems.I just rebuilt my old quad on a new alien 560 folding frame, after much playing about getting everything CG balanced I...
View Article