AMSL Geotagging in MP 1.3.39 does not work - BUG
@coni99 wrote: Hi, the pre-processing step for AMSL geotagging using CAM messages shows this error: Using AMSL Altitude TrueReading log for GPS Messages in order to get AMSL AltitudeError...
View ArticleGrid Overlap in MP and Tower is different with the same settings
@coni99 wrote: Recently I found out that overlap (both side/front) in MP and Tower using the same camera, altitude and overlap settings is different. The difference is around a factor 2. So MP creates...
View ArticleClik here to view.
In Sport_Mode => Throttle 0 = Motor off and PILOT_VELZ_MAX ignored
@DeWe wrote: Hi there, I know that the version 3.2 is normally out of support, but my hope is, that I have make a mistake or must change only an unknown parameter. I use the Mini APM Pro in a small...
View ArticleClik here to view.
Caution! Safety Issue - Quadplane will takeoff if armed and in mode RTL
@JeffBloggs wrote: Hi fellow quadplane flyers and devs. Today we tested the behavior of quadplane whilst armed on the ground. When it is switched to RTL the quadplane will instantly try to takeoff at...
View ArticlePixracer Battery display in MP
@pseddon wrote: With 3.3.4rc1 and an apm power module I find the battery voltage is always 0v in MP but displays correctly in QGroundControl. Is the ESP8266 working in MP? How many compasses should...
View ArticleURGENT Parts List for DJI F550 (hexacopter) running Pixhawk
@eelz wrote: looking for someone to look over our parts list for a project due in 3 weeks! FYI we've ordered everything on this list already...but still we'd need some help! We tried to find...
View ArticleHow accurate should Altitude hold mode be
@Paul-H wrote: Hi all How accurate should a Pixhawk be at holding altitude in Altitude hold mode. Took my new quad out for a spin yesterday and found it did not hold altitude, but I might be expecting...
View ArticlePlane flying right of waypoint track
@BG_UAV wrote: Hey Everyone, I am new to the forums and I need help with my plane's tracking. I setup a survey grid and every time my plane (delta style) it will fly right of the waypoint path. Is...
View ArticleCompile / make file error HELP !?
@Anghel_Alex wrote: Hi all, Anybody an idea ? Trying to compile APM quadcopter with latest nuttx v7.xxNuttx part done, PX4 done , APM I think is done ... This came up :...
View ArticleJob Postings for developers
@CraigElder wrote: http://www.vulcan.com/About/Careers/Job-Listings?jvi=olsA3fwa,Job http://www.vulcan.com/About/Careers/Job-Listings?jvi=oWsA3fwL,Job Posts: 1 Participants: 1 Read full topic
View ArticleEKF_SITL error?
@flyespen wrote: http://diydrones.com/forum/topic/listForContributor?user=1kyxsyes1d373&sort=discussionsStarted Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Need help to analyze DJI flight log
@newmafi wrote: Anybody who can kindly help me analyze the following log?Thank you so much for any precious comments in advance. FlightLog3.png1608x519 13.3 KB FlightLog.pdf (618.6 KB)...
View ArticleLoss of altitude on 2nd flight
@davyg wrote: Had the hexa out last night for it's maiden flight since updating to 3.3.3 Firmware.. 1st flight went well.. take off in STAB mode and then I checked flight modes were working... and...
View ArticleHolybro telemetry radios don't show in Mission Planner
@Bruce_Tuttle wrote: I recently switched to Holybro telemetry transceivers.I am using a APM, Plane. In Mission Planner Sik Radio section, neither of the radio shows any data at all. The old...
View ArticleClik here to view.
Auto Mode Rover Spinning in Circles
@Jimmy_Oliver wrote: My first foray into rovers from building copters. I have finally got the Rover to arm after disabling some arming checks. The first attempt of an Auto Mission (via Tower) has...
View ArticleM8n gps - pixhawk and qgroundcontrol
@djedai wrote: Hello ! I use the Pixhawk flight controller with a u-blox GPS m8n and QgroundControl software. GPS data does not appear in QgroundControl . I tried to modify the GPS configuration with...
View ArticlePixhawk 3.3.3 sr1,sr2,sr3 goes to 0
@cookmangr wrote: HelloI have a hexa with pixhawk and 3.3.3 , for 4 monts working great I ussually connect my tellemetry 433mhz with tower and mission planner and always working very good but today...
View ArticleConditional Commands
@skyveyor wrote: Hello, I've been using Mission Planner for the past six months and continue to learn. Most of my flying is from waypoint to waypoint in auto. At certain waypoints, I want to climb at...
View ArticleAPM 2.6 telem1 port not working?
@tkrneki wrote: HI, I just recieved a new APM 2.6 and soon I realised it's telemetry port doesn't work. I tried the same setup on different APM and it worked, So I opened the faulty APM and all the...
View ArticleClik here to view.
Updated windows installer to resolve "__builtin_bswap16" compile error
@rmackay9 wrote: Since late last week there have been compile issues for those compiling for the Pixhawk family of boards using ardupilot/master. The error was "error: '_builtinbswap16' was not...
View Article