Clik here to view.
DAlt change during hoover with centered Throttle
@lorbass wrote: As shown in the attached pic the altitude changed twice, once by 11m without stick input with 16 Sats.It seems to correlate with the peek on the Sat graphic Steigen ohne Input...
View ArticleArduRover will not use less than 100% throttle in AUTO
@Remi wrote: Hi!I am having a bit of a crisis, and I hope that you guys can help me out. I am working with an unmanned boat that utilizes a APM 2.6 running ArduRover 3.0.1. The two mechanisms that is...
View ArticleCompass ICs support
@wjaxxx wrote: Hi there. With so many compass problems floating around I was thinking in possible solutions by replacing the old 5883 or 5983 by newer and better compasses. So is there support now in...
View ArticleParameters related to brake
@hirochi_hirohiro wrote: Final deceleration of the last way point is rapidly brake is applied. Is there a parameter to relieve this? Posts: 1 Participants: 1 Read full topic
View ArticleCompile Arducopter 3.2.1 with gimbal control for APM 2.5
@Husqy wrote: Hi. Is it possible to compile Arducopter 3.2.1 for a APM 2.5 and leave out Autotune and AC fence to make room for mount control?If possible can anyone point out some direction so i be...
View ArticleTricopter Yaw servo not working
@orion115599 wrote: I recently built a tricopter, but when I attached the tail servo it went to the maximum position and eventually burned out. I tried adjusting the minimum, maximum, and trim values...
View ArticleAPM 2.6 Brownout
@Stephon wrote: Yesterday, I updated my apm 2.6 and calibrated the board. When I was flying, it seemed to work well in stabilize, so i switched to althold then to poshold and all was well. Then I went...
View ArticleQuadplane won't produce enough power to lift off
@HighFlyer wrote: I successfully launched my quadplane on a 3S power system. However, 3S system wasn't enough power for the front plane motor. I then replaced the quadmotors and the front motors will...
View ArticleBuilding APM Planner 32 bit Linux
@ChrisOlson wrote: Running the beta on Ubuntu 16 with the Unity desktop, no issues found so far. I got an old Toshiba Satellite with a 32-bit T1350 cpu that I run Mission Planner on. I'd sure like to...
View ArticleWhere to fine board Schematics for Ardupilot 2.6 et al
@Wally wrote: When adding peripherals or troubleshooting a good schematic is needed. I have not been able to locate any board schematics on the web. There is mention of Eagle files, not that they are...
View ArticleAntenna Tracker and Stepper Motors
@Project23D wrote: I just acquired a couple RV type mobile satellite TV antennas. They have traditional NMEA 17 type steppers in them, and I want to use them with something like the stepper motor...
View ArticleMismatch between number of CAM messages and number of images
@Noosarover wrote: I am doing Survey (Grid) on Mission Planner. I am not getting an image with each CAM message so am then not able to geotag the images using Mission Planner's"Georef images". I am...
View ArticleClik here to view.
Plane V3.6.0 reads Spektrum SRXL input incorrectly
@jrandle wrote: I have been using a genuine 3DR Pixhawk and a Spektrum AR7700 receiver with no problems in my existing aircraft. The receiver is connected to the Pixhawk via its SRXL output. I have...
View ArticleBattery Failsafe not logged
@ist165351 wrote: Hi everyone, I'm using ArduCopter 3.3.3 on a pixhawk board. The other day I was doing some failsafe testings, and intentionally let the battery failsafe trigger twice. Both times it...
View ArticleGopro Camera Control Throw Pixhawk
@ahmed wrote: Hi all , i want to ask dose there any way to control camera ( Gopro Hero 4 Black ) throw Pixhawk and Ardupilot. I need to control some function SwitchON/OFF REC Start/Stop Throw radio...
View ArticleNeeded sabertooth connections and dip switches setting
@shafique_mukadam wrote: I am using an APM 2.6,a sabertooth 2x12 and a transmitter receiver to control a rover. I need the connections and DIP switches setting of sabertooth. If anybody has some idea...
View ArticleClik here to view.
Announcing QGroundControl 3.0
@DonLakeFlyer wrote: We are happy to announce the release of QGroundControl 3.0. QGroundControl provides full flight control, mission planning and configuration for ArduPilot or PX4 Pro powered...
View ArticleRun mission planner with config from command line
@slimmons wrote: I'd like to be able to start mission planner from the command line, and also specify a waypoints file to use. For example Right now I can start mission planner by running: C:\Program...
View ArticleNewbie question on stick assignment
@phlounda wrote: Hello,My pitch and yaw are on the wrong sticks. Pitch is left/right on the left stick, and yaw is forward/backward on the right stick. Throttle and roll are correct.Can I change the...
View ArticleMultirotor name mission planner
@icvdok wrote: Hello everybody, Just a simple question but I didn't find the answer searching on the forum. I've a couple of multirotor Hex, Quad, etc., each of them flight with Pixhawk FC. When...
View Article