Ardupilot with downstream FBL controller for traditional heli
@InvertedCNC wrote: Greetings! I just stumbled upon this article on DIYDRONES about an RC pass through to allow use of a traditional FBL controller...
View ArticleSkid steer problems with changed RC map
@derelicte wrote: Hello, I am building a rover based on a remote control John Deere tractor for my kids to drive their dolls around in. It has an articulated body that uses skid steering driving the...
View ArticleClik here to view.
Hex Crash with 3.3.3 - Odd motor shutdown logic
@figure8 wrote: Hello Working on discovering why one of our hexcopters dropped out the sky from 30m (not too much damage ) Was basically in Alt Hold mode, with gentle moving around, in fairly windy...
View ArticleClik here to view.
Erle Copter in indoor environment project
@mrmrzamany wrote: Hello , So I want to fly the Elre Copter in indoor room and I have some questions:1- since the GPS is disabled in indoor environment, which modes can I use to takeoff and land...
View ArticleLoiter_to_alt and guide mode doesn't work if I set Q_guided_mode to 1
@farstein wrote: Hi friends: As I describe, the Loiter_to_alt and guide mode doesn't work if I set Q_guided_mode to 1. And when I set Q_guided_mode to 0, it works well.And another problem,,when i set...
View ArticleClik here to view.
APM Planner 2.0.23-rc3: Download Log Retransmitting
@lasakro wrote: I'm recently a Linux convert so still a beginner using APM Planner as GCS. While downloading a log file it's extremely slow and mostly sits at "Retransmitting". This happens via USB @...
View ArticleNo drone location available ?!?
@mapmart wrote: Hi! I just startet out with pixhawk and am trying to get tower to work on my tablet but I´m not getting any coordinates transmitted. I know i have a GPS fix because tower correctly...
View ArticleScreen recording a Tower mission
@DarylWM wrote: Hello, I tried to record the tablet screen while Tower was running a mission so that I would get the map and video feed, but the screen recorder I'm using (AZ Screen Recorder) kills...
View ArticleArducopter 3.2.1 Autotune Problems with Low Kv Motors
@Teknopaul1 wrote: Just finished building 500 size quadcopter with 750 KV motors, Simon K ESCs and 11' props. Have loaded Arducopter 3.2.1 and activated Autotune on CH 7. When Autotune is activated it...
View ArticleAPM 3.6 Flight Mode Initializing Issue
@codeforge wrote: Hi,recently i bring out my 3dr apm board 2.6 with external gps and i want to make my skywalker x8 fly again. Then i download latest mission planner (not apm2 planner) and flash the...
View ArticleClik here to view.
APM Planner 2.0.23-rc3 Extended Tuning Values not Populating
@lasakro wrote: On the Extended Tuning page the Stabilize and Rate values for all 3 axis are not populating from the full parameter list. Even after Refresh Params the values remain at zero. Same...
View ArticlePixhawk 2 Alpha test logs
@Blitz wrote: https://www.dropbox.com/s/fbe7gogutx6nd0h/2016-08-07%2010-52-23.bin?dl=0 Posts: 1 Participants: 1 Read full topic
View ArticleNeed Help to for custon firmware
@Nicolas_Schnyder wrote: Hello Guys, im new in the forum, but flying with Pixhawk for two years with several platforms both fixed and rotary wing. Im very used to in the setup, but now i have a...
View ArticleLightWare is now ISO9001:2008 certified
@Nadia_Nilsen wrote: We would like to share this exciting news with the ArduPilot community:LightWare is now ISO9001:2008 certified Posts: 1 Participants: 1 Read full topic
View ArticleCopter-3.4-rc2 available for beta testing
@rmackay9 wrote: Copter-3.4-rc2 is now available for beta testing through the Mission Planner’s Beta Firmwares link. A relatively complete list of changes are available in the ReleaseNotes.txt but...
View ArticlePixhawk 2.4.8 motors run briefly after cutting throttle
@pmshop wrote: Throttle cut issue with PixHawk 2.4.8 running firmware for Quad or Hexa 3.3.3.Quad shown for reference.The motors keep running after throttle is cut.Not "keeps spinning", motors are...
View ArticleElevon mixing not working
@anparkinson wrote: I have a DX8 transmitter set to normal wing setup - 1 servo for aileron and 1 for elevator. My plane is a delta so of course when I move the stick to go up and down the right side...
View ArticleClik here to view.
Simple and Super Simple help needed
@Paul-H wrote: Hi all Being a bit Simple Simple and Super simple sound to made just for me, so I enabled Super simple on Channel 7 and have it controlled via a 3 way switch which according to my...
View ArticleClik here to view.
Mission Planner v1.3.39 Errors with Mono and Ubuntu 16.04
@lasakro wrote: I'm connected to a Pixhawk by 3DR Radio and running AC v3.3.3. Everything other than the 2 items below seem to work fine. The MP Build is 1.1.6038.12291. With a mission loaded I select...
View ArticleHexo plus copter Pixahawk problem,
@Kev_N_Groom wrote: HI, I have a Hexo plus hexacopter that always starts with this error message although the parameters and connection seems fine. It always sats PreArmCheck: HEX FFFFEOOO. Does...
View Article