Creation of Waf tool ap_persistent and build issues
@guludo wrote: Hi all, We've pushed some changes recently from https://github.com/ArduPilot/ardupilot/pull/4590 that, among other things, create a new Waf tool called ap_persistent. That reduces clean...
View ArticleTarget Airspeed changes when TRIM_ARPSD_CM isn't an integer value in m/s
@paan2097 wrote: I am running arduplane in SITL and noticed that in my tlog or the status tab in Mission Planner that my target airspeed constantly changes if the targetairspeed isn't an integer...
View ArticleDO_SET_ROI in ArduPlane
@Markus_Dillinger wrote: As far as I know, regions of interests to point the gimbal camera at is only available in the copter firmware,is it also possible on the ArduPlane firmware? With a gimbal...
View ArticleChanging the height during auto mode
@Kehne wrote: Hey guys, I'm building a solar powered airplane and would like to fly a complex mission. The airplane should circle the whole time, but change the flying high in condition to the battery...
View ArticleFailed Pre-Arm Checks (Double Amber) - Troubleshoot
@John_Easton wrote: Completed all the options under mandatory in initial setup and all was successful Result - 1 - Pixhawk LED - double flashing amber (failed pre-arm check)2 - Safety switch triple...
View ArticleClik here to view.
Can´t connect with UDP / PXFmini
@Cyrgon wrote: Hello everybody, i´m Endric and i am an newbie with Mission Planner.Sorry for my bad english, but it´s not my vernacular language. Now my DIY Drone is ready and with help from Erle...
View ArticleCrash on 550 quad with Pixhawk on 3.3.3
@DaveP wrote: I have been having considerable problems with my 550 quad after having installed a Pixhawk clone from RcTimer. I downloaded Copter 3.3.3 hoping it might cure the wildly rolling craft...
View ArticleMP v1.3.39.2 - survey grid anomoly
@timvand wrote: When planning a grid, here are the results, as expected.http://prntscr.com/caswvh After accepting, this is the new mission.http://prntscr.com/casxb5 Is this some new fangled feature?...
View ArticleHello here a problem with AutoTuning pixhawk
@cuchara wrote: when I put the drone in AutoTuning the drone loses altitude and crash Any idea what I can do?Thank you Posts: 2 Participants: 2 Read full topic
View ArticleClik here to view.
Why I can not use channels 9 and 10 ? HobbyKing's- HKPilot 32 Controller
@cuchara wrote: Why I can not use channels 9 and 10?I try to use the channels 9 and 10 of the transmitter with the HobbyKing's- HKPilot 32 Controller , but does not work. why?...
View ArticleCan't get Pixhawk to go into AUTO?
@John_Easton wrote: After several issues with pre-arm failures on my sonar survey boat after a firmware update I still can't change the mode from Manual to Auto - it forces itself into HOLD. Any help...
View ArticleGood progress on quadplane testing but can someone check out my logs please?
@jacques_eloff wrote: I’ve made some good progress on getting my Observer/Ranger-Ex Quadplane dialed in. I’ve done 4 transition flights and about 20 hover tests and, whilst it is much better after...
View ArticleAPM copter 3.3.3 Guided mode with companion computer
@Muttle wrote: Hi all,I have a trex450 conventional helicopter running a px4 with an intel edison as a companion computer. This system has a custom build linux ubilinux install and runs ROS Indigo and...
View ArticleVery hard landing (crashed landing gear) when RTL after 10 minutes succesfull...
@alpa2009 wrote: Hi,I did my first flight with a pixhawk (original) controlled 12 motors dodeca hexacopter. All went well (stabilize and Poshold modes) until I tried to land with RTL mode. It went to...
View ArticleUnexpected throttle zero in pos hold
@Hubertus_Paetow wrote: Today after flying around in stabilize i switched to pos hold and contiued flight. after about a minute without any action the motors stopped and copter started falling. I...
View ArticleClik here to view.
Terrain altitude during the flight
@sibsky wrote: Hello, APM users Guys from DIYDrones recomend to ask here. As we knew during flight planing we could see altitude of each terrain point on map loaded (right up corner of flight plan...
View ArticleCommands change with copter orientation
@mickaeldes wrote: XHi, I bought a DIY drone on amazon and I mounted it. I did all configurations thanks to Mission Planner. And I tried my first fly... but during it, the commands changed with the...
View ArticlePlease help 2.8 how do you download the soft where f
@wacked wrote: I have a new 2.8 how do you download the soft where for it? I have windows Vista.Thank youTerry Posts: 1 Participants: 1 Read full topic
View ArticleBasic Setup for Dummies
@John_Easton wrote: I will be deleting and replacing this first post with all the little things I have learned from the gurus on this board, particularly David Boulanger and Michael Oborne, that have...
View ArticleClik here to view.
Rover 3.1 Build (Traxxis Stampede)
@billb wrote: Ok, my first adventure in to Rover is starting and its going to use a Traxxis Stampede. I just happened to be at the park with the kids and a conversation about my flying toy drone ended...
View Article