Strange roll in auto mode and recover AP3.5.3 (almost flyaway?)
@terseven wrote: Hi everybody, I am new to this forum, so if there is any rules or anything, please let me know. In this case, I suffered a strange tendency while my plane was performing an auto...
View ArticleClik here to view.
DIY Octo flies away during Loiter and RTL
@camoklr wrote: I am very new to this whole hobby so pls be patient with me. I was given a Octocopter with 570kv motors, 13x6.5 props, APM 2.6, Ublox GPS. The previous owner built it and maiden it....
View ArticleMaxbotix I2C Range sensor parameters?
@antonvh wrote: Hi, I try to get data from a maxbotix i2c sensor. I ordered the type described in the manual...
View ArticleFutaba SDUS extra channels
@ardisd wrote: I have a futaba14mz with a TM-14 2.4 GHZ module and R6208SB receiver. After I upgraded to Copter 3.4 and did a quick test flight which went well, I decided to tidy up the RC 9 to RC 12...
View ArticleCannot connect Tx to MP, no com port?
@butchalline wrote: MP 1.3.41APM Copter 3.4.1Win 10 Yesterday I loaded MP, installed firmware on quadcopter, connected Taranis,did initial setup, flew quad copter no problems. Today, attempted to do...
View ArticleVcc min/max difference exceeded
@wcfung1 wrote: My recently assembled S500 quad was flight tested with Pixhawk running Copter 3.4.1 has the following warning on Log Analyzer in Data Flash Log :-- Vcc = WARN --- Vcc min/max diff...
View ArticleClik here to view.
Waypoint flight route.How to fly along the line?
@duxin wrote: hi, everyone! I met some problems about tracking error during way point flight in auto mode. I'm using a qudurotor to do a task about WPnav flight indoor recently. The its actual flying...
View ArticleClik here to view.
Calling all testers! New ArduPilot sensor drivers
@tridge wrote: We have just implemented a major upgrade to the ArduPilot sensor drivers for STM32 based boards (PX4v1, Pixhawk, Pixhawk2, PH2Slim, PixRacer and PixhawkMini).The new sensor drivers are...
View ArticleNo compass calibration yet there is IMU calibration
@Graham_Dyer wrote: Once setup on my multirotor I wanted to use Tower on a tablet to do some flying. When I got to the flying area I had to do a compass calibration due to many compass...
View ArticleClik here to view.
ArduPilot New Sensor Test
@cala2 wrote: First test: a Robocat 270 with 2350 kv motors, 30A esc with oneshot disable 2200 3s batt and in process to tune; I upload latest vers and try as it.Yaw I know that it was untunned, pitch...
View Article3.4.1 reporting altitude Above Sea Level
@pmshop wrote: 3.4.1 is reporting ASL instead of AGL.I had one issue fixed with DroneLogbook.com, couldn't even upload a 3.4x log.Now DroneLogbook says the only altitude reporting is ASL...which is...
View ArticleDo vibrations have an affect in stabilize mode?
@bisenberger wrote: My quad was making sudden altitude changes in stabilize mode. I checked the logs and the vibration was quite high. Posts: 2 Participants: 1 Read full topic
View ArticleSensor Update Build with Crash log
@Lance_B wrote: Had a gnarly little crash. And there's a lot going on here since I'm testing multiple things. This was odd since I've flown it several times on this build. When it happened, I'd just...
View ArticleCopter crash after retract landing gear - Request for help
@tsahim wrote: Hi,I need help with analyzing sudden crash to my new Tarot X6. Frame: Tarot X6 and its landing gear.FC:PixhawkVersion: copter 3.3 Retracts are basically connected to the PDB for power,...
View ArticleFullscreen video?
@Andre-K wrote: Is there no option to make video go fullscreen, or is it just me ? Posts: 3 Participants: 2 Read full topic
View ArticleMP not saving Joystick settings
@Lat_Long wrote: Hi Everyone, I have just upgraded my MP and now when I set all of the channel controls for my Joystick I hit save. If I close the joystick window and then open it again all of my...
View ArticleClik here to view.
Autotune log with Big Propellers no good yaw settings?
@mpircher wrote: Hey, 3.4.1 full autotune, quad + , BIG propellers 30", aggr 0.7, -15° cold www.dropbox.com logs MD4100 Shared with Dropbox what do you think ?Yaw seems unstable in hard turns, the...
View ArticleClik here to view.
3.4.1 Loiter_Time increases altitude at LTWP
@pmshop wrote: I noticed in firmware 3.4.1 that there is an increase in altitude by about 10 feet when the craft reaches the Loiter_Time command point. According to my Flight 3D replay, the craft...
View ArticleQuadplane spinning on takeoff
@darrell wrote: For the last couple of months I've been trying to track down the cause of a quad plane running 3.7.1 that spins (yaws) on takeoff. While this type of thing typically is related to...
View ArticleMatlab to MySQL
@krisclarkdev wrote: All, Firstly, hi! I'm a new member to the forum and extremely new to the hobby of RC aircraft. Secondly, I did some looking around for a better way to review tlogs and couldn't...
View Article