New un-understandable error message
@Detleff wrote: Yesterday, I got a new error message that I am totally puzzled about. Mission Planner showed: EKF2 IMU0 ground mag anomaly What does it mean?Where does it come from?How important is...
View ArticleMinim OSD V2.0 connection to PC via FTDI
@wcfung1 wrote: I bought the OSD from following vendor :http://www.goodluckbuy.com/crius-mavlink-osd-v2-0-minimosd-compatible-atmega328p-microcontroller-dc-dc-voltage-stabilization.html Had problem...
View Article3.4.1 will not calibrate
@pmshop wrote: On my Quad 3.4.1, everything calibrates fine (except a compass issue of high offset no matter how I calibrate).But on my HEX, 3.4.1 refuses to calibrate the accelerometers. Also noted,...
View ArticleAbout ROS/Gazebo Simulator with SITL?
@Mandeep_Singh wrote: After so many days i started understanding about the whole pipeline and after fixing bugs that came during set up, today i just find out that the page...
View ArticleCopter-3.4.2 released
@rmackay9 wrote: Copter-3.4.2 has been released and can be downloaded from the Mission Planner and other GCSs. Changes from 3.4.1 are listed below: 1) Minor Improvements: ACRO_Y_EXPO applies to all...
View ArticleOld RC compatible
@bandini wrote: Hi circumstances that are beginner I have an APM 2.5 ardurover and an old rc 26,660 Mz receiver with 2 channels.I tried to connect it with negative results.They may not be...
View ArticleQuadplane with 4 motors
@piotr_coner wrote: Hello,Is it possible to configure arduplane on pixhawk to to work like on this "nasa bixler" : https://www.youtube.com/watch?v=e7QNbU71lsA&t=202s quad plane on only 4 changing...
View ArticleAPM 2.8 vibration Accz too much and away 0 level
@Pilot2016 wrote: Hi I am working on APM 2.8 and after learning too much atleast its flying and hovering in acro and stablize mode. Now my target is to reduce the vibrations at a level where I can try...
View ArticleAltitude lost and regained in Guided mode, but holds steady in Auto mode
@AlexL wrote: Hello! When I execute a flight plan in Auto, the quad holds altitude nicely as it moves from waypoint to waypoint. When I change the flight mode to guided using the Tower app and command...
View ArticlePixhawk2 setup with AR7700 receiver
@gpetty wrote: I'm just getting started learning how to work with my new Pixhawk2 autopilot to convert a fixed wing RC plane to an autonomous UAV, and I have found that online documentation for the...
View ArticlePixhawk HC-SR04 sensor Connection
@salonijain12 wrote: Hi All, I am trying to connect HC-SR04 ultrasonic 4 pin sensor to pixhawk flight controller for obstacle detection.HC-SR04 has 4 pins: 5V Supply, Trigger pulse Input, Echo pulse...
View ArticleCrash logs analysis
@Thonon wrote: Hello I have a fixhawk rctimer:Frame tarot 650telemetry 433mhzTaranis and delta 8I flew with 3 times without worries.Today i install:gimbalgoprotx videoRepeater with turnigy 9xI flew...
View ArticleSeems to be a Bug
@Fernando_Mosquera wrote: Hi guys, I´m running the latest up to date MP version with APM 2.7.2 (from HK) with APMPLANE 3.4.0 firmware via data radio. Everything seems to be fine, except for radio...
View ArticleI'm running 3.4.2 Arming checks
@OAPpilot wrote: HiI can arm my Pixhawk without it doing arming checks, even though they are turned on in Mission Planner. i.e No Sats etc. Is there another param. that needs to be changed? Posts: 4...
View ArticleFly by mavlink topic?
@dpsoul wrote: Hi,I am thinking of using raspberry pi or similar computing platform for maneuvering quad using joypad on the ground.Has anyone done this? Posts: 2 Participants: 2 Read full topic
View ArticleHello, I am new to this forum, and in ardupilot
@nano1234 wrote: Hello, I am new to this forum, and in ardupilot.I installed the ardupilot in my plane and configured everything, at least I think.But when I put it in RTL mode, Circle ... the engine...
View ArticleOctoquad with pusher
@CatiaDr wrote: Has anyone here tried using the Quadplane code in an X8 configuration with a pusher motor? We have it working on a Pixhawk with Quad motors but need the extra lift of an X8. Posts: 1...
View ArticleNo logs on pixhawk?
@larsks wrote: I wanted to review the logs on my pixhawk (running APM 3.4.2) after a flight went awry earlier today...but connecting with mavproxy and running log list reveals: STABILIZE> log list...
View ArticleClik here to view.
Question on AUTO mission start with copter and with plane
@aamadeuss wrote: Hi, i have some questions to the AUTO missions with pixhawk wiht copter and plane. copter:usualy i upload my mission, arm, take off in stabilize than switch auto and wait until the...
View ArticleClik here to view.
Thank goodness for RTL
@larsks wrote: I guess this is a "Rave" rather than a "Rant". There is nothing like seeing $1500 fly off over the trees and out of sight... ...only to return as if by magic once you have the presence...
View Article