MANAGE DATA FLOW FROM UAVCAN Equipment to Pixhawk
@Alexis_Frerejean wrote: hello I am using ZUBAX GNSS2 for external GPS, Compass and barometer My request is about best "Publication interval" according to sensor for Pixhawk to ba as efficient as...
View ArticleCompass not accurate
@anparkinson wrote: I have calibrated my compass on the Pixhawk but it always reads about 20 degrees out if a lay a regular magnetic compass next to the plane. How can I sort this? Thanks Posts: 1...
View ArticleClik here to view.
Mission Planner Connection Error
@ultra6a wrote: I get the attached error message every time I try to connect to Mission Planner. No problems before I had to format my hard drive and reinstall every thing. Now I get this error...
View ArticleClik here to view.
Can't connect LiDAR-lite V3 to Pixfalcon via I2C
@brewkon wrote: I am trying to connect a LiDAR-lite V3 by Garmin to a Pixfalcon with copter 3.4.6 via I2C. I can’t enable the Sonar in the initial setup page the enable button is blacked out. After...
View ArticleOLED display - Pixhawk-1 Copter 3.5-RC3 QGCS 3.1.3
@Arbutus wrote: The Adafruit OLED SSD1306 display can apparently connect to the Pixhawk-1 via I2C. I have flashed with 3.5-RC3 but cannot see any parameters that affect the display. For example...
View ArticleGazebo sitl sim
@jakkala_kalvik wrote: Is there a tutorial to communicate with a drone in gazebo with ardupilot plugin from ROS apart the tutorial from erle robotics. Erle robotics is not using the standard version...
View ArticleClik here to view.
Command delay in absloute time and polygon fence in rover
@Dorian wrote: Hello, I Have already asked my questions in the rover 3.1.0 category, but I did not get an answer. This concerns Rover: Firstly, It-is possible to have the Mission Command “Delay” in...
View ArticleCrash analysis trex 450
@ivank wrote: Hi allfew days ago my heli crashed but i dont know why.crash happen when i switched from stabilize mod to althold mode,heli just tipped over and went straight to the ground,i got warning...
View ArticleWhen I cut the throttle to zero IN FLIGHT, the system disarmed, and my drone...
@Tom-Shen wrote: Days ago, I flew my drone quite high, flight mode is Loiter, I want it landing quickly, so I put the throttle to lowest position, after like several second, I found my machine...
View ArticleRetired Board APMpro problem
@Crane wrote: I am using Mini APMs and a recently purchased APMpro. A couple of days ago I got the message 'retired board...will upload latest firmware AC 3.2.1/AP 3.4.0'. Now I get the same message...
View ArticleCopter - 3.4.6: RTL Land At Wrong Location After Battery FS
@Mike1 wrote: I loaded Copter 3.4.6 on my Pixhawk this weekend to do some flying in auto mission. I wanted to test out some of the FS options. I experienced a behavior I cannot explain with battery...
View ArticleMultiple UAV Mission Planner
@BFM1 wrote: Hi all, I posted this in MP three but no joy, I'm looking to do a multiple UAV setup drone and rover and was reading the below regarding poor performance over the...
View ArticleClik here to view.
No Led of the FMU lights up and the Pichawk heats
@IsmaT wrote: Hello?I need some help, i was using my Pixhawk1 and when i plug the USB to use it, No Led of the FMU lights up and the Pichawk heats any solutions ?This is a picture of my issue Posts: 1...
View ArticleAnybody else actually using an Edison on board? Having issues
@Lance_B wrote: I received my unit last week - finally. Pretty impressive quality and a good selection of included accessories. The hex screws on the bottom cover could go away however, now that I've...
View ArticleClik here to view.
Results on single frequency RTK for drones
@miquel wrote: Dear colleagues, I would simply like to share with the community some results we've got on our RTK processing for our GNSS receiver (Argonaut) maiden flight with a fixed wing drone....
View ArticleError first compiling ArduCopter with Make (Windows 8.1)
@Alex94cerio wrote: Hi everyone!I'm trying to compile the ArduCopter code with make px4-v2 on Windows 8.1 but I get ERROR 1This is the log: Alessandro Cerioni@Alex /c/GitHub/ArduPilot/ArduCopter $...
View ArticleHelp simulate custom ArduCopter code (Mission Planner)
@Alex94cerio wrote: Hi everyone!I would like to test my own ArduCopter code with the simulator of Mission Planner, and I don't know how to do this.I saw that the code needs to be an image file, how...
View ArticleClik here to view.
EKF blew up during onboard calibration
@PittRBM wrote: dropbox.com CompsCal.bin Shared with Dropbox Log of me rotating the heli during on-board compass calibration. After a couple of axes, EKF blew up. Clicking yellow EKF text shows 3 of 5...
View ArticlePPM channel keeps switching on BeagleBone Blue
@karthik wrote: Hi, I'm using a FS-A8S reciever with PPM out on the BeagleBone Blue. I've noticed that the channels get scrambled when connected to RC i.e. channel 3 gets assigned to Yaw/Roll. This...
View ArticleMotors start with Throttle down. Calibration OK
@FlyingPenguin wrote: Hi Ardupilots, I have done the calibration which has succeed. Throttle values are between 1002 and 1997 on Mission Planner. When I arm the motors, they start to spin. But the...
View Article