Types of frames, design ideas etc
@jpkh wrote: What type of boat frames our users would like to see. What type of categories people are usually using. Thread to create ArduBoat preferred reference frames. Monohull,Catamaran,Racer,What...
View ArticleClik here to view.
Sony A5100 CAM_FEEDBACK_PIN Flash mod for CAM evnents
@mpircher wrote: Hey guys, i try to mod my A5100 to have a output cable for the feedback pin.would that be possible with modding the flash? 1.jpg874x724 98 KB 2.jpg783x821 91.4 KB think it should be...
View ArticleAPM 2.6 response only once after REQUEST_DATA_STREAM
@Asaf_Sarid wrote: I am trying to get mavlink messages from APM 2.6 via telemetry that is connected to my ordoid u3 usb port. I am able to read messages when I send the REQUEST_DATA_STREAM message,...
View ArticleOptical Flow positionning behavior with LOG
@kuspower wrote: Hello, Today other test show that OF it's perfect at low height <10m above gnd. Pilot can put pitch/roll stick input at max and copter 3.4 handle it well limiting max velocity...
View ArticleCouldn't enter PosHold. EKF and FlightMode errors
@wicked1 wrote: I've had a couple flights now where pos_hold doesn't do anything..Today I changed it to Loiter, and it worked.So, I checked my last PosHold log, and see Err: EKF_Check-2 and Err:...
View ArticleAuto-Take-off to set Alt
@GertJL wrote: Hi All, Does Copt3.3.3 support this feature/function? (which I believe is possiblewith DJI Ph) - The pilot initiate Auto-take-off, the vehicle launch andauto-take-off to a set height of...
View ArticleAuto-takeoff to a set Altitude - mode?
@GertJL wrote: Hi All, Does Copt3.4 support this feature/function? (which I believe is possiblewith DJI Ph) - The pilot initiate Auto-take-off, the vehicle launch andauto-take-off to a set height of...
View ArticleAltitude issues in Loiter, high Nav pitch demand, abrupt crash in Fly by wire
@Nihal wrote: Hi, I had a routine flight for an hour or so with my pixhawk in arduplane 3.5.2. The plane flew well for about fifty minutes or so in auto. After that, I switched to loiter a couple of...
View ArticleAltitude Drops in Loiter and subsequent crash in FBWA
@root wrote: I flew my XUAV talon today with my PIxhawk running arduplane 3.5.2. The flight lasted an hour or so and was smooth until the last couple of minutes. Here's what happened. On switching to...
View ArticleRC6 passthrough (set in mission planner) where is it then going?
@henrik04 wrote: Silly little problem:Pixhawk connected to a FrSky 8 channel receiver.Set RC6 to passthrough in mission planner. (and write the data to the pixhawk). Tested the pixhawk AUX channels...
View ArticleApm pro mini ppm problem
@hosoludi wrote: Hey I ve a problem with my apm pro mini. Cant get my ppm receiver working. Do not even got power on it. I use a junper for 2 and 3 and put the receiver on channel 1. Can someone tell...
View ArticleApm pro mini minim osd problem
@hosoludi wrote: Hey I have s Problem with my minim OSD and my apm pro mini. Ive connected soldered the pins fot the 5v power on the minim osd . I also power the cam and vtx direct from the current...
View ArticleFormation flying with arduplane
@yuval wrote: Hello,Recently me and my friends started flying a formation of FPV planes.I have noticed that finding my friend plane while flying is really hard and takes some time. I was wondering if...
View ArticleSupport training, log analysis
@timvand wrote: All, Is there a plan to create a knowledge base, or log analysis tools? Here is my issue. I have some logs and there are error:cpu1 and error:cpu0 in a couple of the files, and then in...
View ArticleActivating two relay signals from a hand controller
@rusttree wrote: I'm trying to activate two separate devices from my Pixhawk on an X8 using the aux outputs as relay signals. I'm able to get Ch7 on my hand controller to activate the relay signal on...
View ArticleAux outputs help needed
@Paul-H wrote: Hi all Don't know if I have read the instructions correctly or if I am trying to do something that is not possible, but I have Arducopter loaded to my Pixhawk and use a 10 channel radio...
View Article***Delete this post
@timvand wrote: ******DELETE THIS POST Reposting elsewhere Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
CPU and EKF error
@timvand wrote: Having an issue with a rig that is flying erratically. What is the meaning of the error, err:cpu-1, err:cpu-0 160621_10.bin.jpg1189x493 101 KB 160621_11.bin.jpg1189x754 169 KB And what...
View ArticleAPM 2.8 PosHold mode problem
@Mehras wrote: HiI cannot set the PosHold mode, when radio pwm is in range of the PosHold flight mode, the mission planner execute the mode which i've set prior to poshold, although HDOP is below...
View ArticleMission Planner loops endlessly analyzing dataflash log file
@wkf94025 wrote: MP Log Analyze screen shots 23jun16.pdf (971.6 KB)I have been trying to convert a dataflash log file to .txt for viewing/filtering/sorting in Excel. I am running MP 1.3.37. Some...
View Article