Pixracer clones 3.4-rc3/4 error
@wifiguru10 wrote: So I got stuck with a clone board. Been trying to order one from AUAV but they're out, thought i'd check out the clone and see how it worked. So i found out that with 3.3.4 it...
View ArticleClik here to view.
Vertical Velocity Discrepancy
@Anthony_Merlino wrote: We’ve had a few flights on a Pixhawk S800 setup running Copter 3.4rc2 where the altitude hold is poor. The interesting thing is that a power cycle (no config change) usually...
View ArticleClik here to view.
Uncommanded Yaw Copter 3.4rc2
@Anthony_Merlino wrote: Here are some files showing an anomaly with yaw running Copter 3.4rc2 last week. After switching to Stabilize and starting to descend, the Hex did an abrupt uncommanded yaw of...
View ArticleElevon Hard Over
@mickmc wrote: Hi GuysHave been setting up a Go Discover with an APM and 3.4. I have flow in manual and FBWA but when I switch to AUTO or Loiter I get almost full left elevon. I have flow an Autotune...
View ArticleClik here to view.
Scratch Built Micro Quad Copter
@jolin wrote: A few years ago I purchased a mini quad copter for myself as a christmas gift. I learned to fly this mini quad copter and that inspired me enough to build a DIY quad copter. I decided to...
View ArticleClik here to view.
QuadPlane help for code
@maelito wrote: H all, I have a project of building a quadplane with a servo to control the angle of the 4 motors.It's different from all the Quadplane projects i saw on the forum do I started...
View ArticleCopter-3.4-rc5 soon available for beta testing
@rmackay9 wrote: Copter-3.4-rc5 is available for beta testing. Release Notes are copied below. As per usual, the firmware can be downloaded from the Mission Planner's Install Screen's "beta firmwares"...
View ArticleFirmware.ardupilot.org down?
@Offlinemaker wrote: Hi guys,Been using MP for years, wanted to start my personal season by configuring my updated build.But I cant download anything, the dl links in the Wiki are dead and...
View ArticleCrash Pixhawk Arducopter 3.3.3 Help
@mxapaza wrote: Hi, I´m Max recently I replaced my Arducopter with Pixhawk. I performed all configurations and calibrations. In hexacopter test flight the controls don´t respond and finish with Drone...
View ArticleQuestioning Pixhawk2 design choices
@Hugues wrote: POST deleted. Subject impossible to discuss constructively. Posts: 22 Participants: 10 Read full topic
View ArticleNeed a sanity check for message constructed using the MAVLink api (1.0)
@Travis wrote: I wish to use a BeagleBone Black to send MAVLink messages to a PixHawk via. the telem2 port. I am using a basic USB based FTDI serial converter that has its jumpers set to provide 5V...
View ArticleWaypoint altitude response
@Pedals2Paddles wrote: I have some missions coming up that have significant altitude changes throughout. Some are due to steeply rising terrain. So I need some verification on how AC responds to...
View ArticleUpdating ArduCopter
@Nerox wrote: Hi guys, I'm going with my perfectly functioning copter to Ibiza soon, expecting to shoot some great videos. I'm running a Pixhawk with Copter 3.3.1 that has been carefully calibrated -...
View ArticleHelp understanding why RTL was triggered in auto
@Tim_D wrote: I have built a new wing that I can use for mapping. I ran my first auto mission today but can figure out why RTL was triggered half way through. I dont think it was a radio failsafe. If...
View ArticleDisarm/Arm in the air
@Jman841 wrote: I was testing Plane 3.7 today and has 2 issues. Getting the compasses to not throw an error is becoming more of an art than a science. Had to redo the compass calibration about 3 times...
View ArticlePerfecting the reverse thrust landing
@Jman841 wrote: So today I did some more experimenting with reverse thrust landing and am wondering if anyone else has experimented with reverse thrust landings without a LIDAR. I think the LIDAR will...
View Article700 class gasoline heli
@hirochi_hirohiro wrote: Controller Pixhawk(AC3.3.3)GPS M8NTelemetry Xbee(2.4GHz)Engine OS-GT15HZ(25:1)Throttle controller Futaba GV-1 Stabilize OK.Alt Hold OK.Loiter OK.PosHold OK.RTL OK.Circle...
View ArticleNon - standard mission planning
@flybarless wrote: Hello, I am using mission planner for flight planning purposes to perform NADIR ortho-mosiac. As 3D mapping using cameras which aren't aiming "90 degrees to the ground" (NADIR),...
View ArticleClik here to view.
450 heli multiblade with Apm 3.1
@IcescuI wrote: Hi all,im setting up a trex450 with apm 3.1, i would like to install pixracer in future but apm was in the drawer...the multiblade head is phased at 90 degrees, someone knows if i...
View ArticleNot functioning gimbal by setting up in Mission Planner
@Quadflyer wrote: Hello everyone, I almost finished my Xaircraft X650 pro with Pixhawk flightcontroller. The Autotuning went very well and the voltage is very well to. The quadcopter flies very, very...
View Article