ArduPilot Copter Consultants Available?
@poirierp wrote: Hello, I am new to this forum so sorry if this is repeated. We have recently decided to switch to using PixHawk hardware with ArduPilot for our UAV platform. We are having some...
View ArticleAbout Mission planner, Arduino to Pixhawk
@atomsbaza wrote: Hi all I have some question about my project. I have old DIY drone using Arduino Due 32 bit from my senior my aim for this project is about avoidance system for quad copter by using...
View ArticleCAM_TRIGG_DIST missing in the Full Parameters list?
@Ali1k wrote: I was going through a tutorial and got the camera going etc. But on the step where i setup the CAM_TRIGG_DIST in the Full Parameters list i search for it and cant find it. I might be out...
View ArticleSensor tests messages
@Carolina_Cec1 wrote: Hey guys!i would like to run the exemple codes of sensors (like AP_Compass_test) and see the messages that are printed.But i don't know how i can see the messages since the CLI...
View ArticleJerky servos through manual mode APM 2.6
@Vlad wrote: Hello, I have APM 2.6 on my Mako. For some reason the servos are kind of jerky, not smooth in the operation when I move the sticks in manual mode. It still flies good as is. However when...
View ArticlePixhawk is suddently bricked
@paan2097 wrote: I've been successfully using my Pixhawk for the past week. After connecting it to a 5V 2.5A micro usb power cable, the pixhawk will no longer boot. The PWR lights are on, the I/0 B/E...
View ArticleSpec'ing out a piezo buzzer for Pixhawk2
@rusttree wrote: I'm designing a Pixhawk2 carrier board and want to include a piezo buzzer mounted on the PCB (like the Solo carrier board). So I checked the specs on the Solo piezo buzzer, which is...
View ArticleMotor arm/disarm with a radio switch
@riveraj wrote: Good day i know this topic has been brought up before, feature requests have been submitted. I wanted to ask again. Its 2016, ArduCopter 3.4 is in development. Has the ability to motor...
View ArticleWhat board type is Pixfalcon
@jasonshort wrote: I'm setting up Pixfalcon I had in a drawer and the it wants a BRD_TYPE param to be set. What is the matching index for the Pixfalcon? The wiki fails to mention this APM compatible...
View ArticleExtended Tuning screen in APM Panner
@jasonshort wrote: My extended tuning screen doesn't seem to work now that I've updated to rc-4. All the attitude and rate PIDs are now 0. Is there a beta Planner out that works? Thanks,JS Posts: 5...
View ArticleHigh Internal Compass offsets
@swiggsy wrote: Hi All, I am after some help with a compass issue. I have a Pixhawk running Copter 3.3.3 and after performing a compass calibration I always wind up with offsets around: x:150 y:-700...
View ArticleCrashed Skywalker Arduplane 3.40 when switched to RTL while the plane was in...
@Rana wrote: Hi, Crashed Skywalker Arduplane 3.40 when switched to RTL while the plane was in guided mode "Go to Here" I can see that there is no Airplane firmware upgrade for APM beyond 3.40 and I...
View ArticleGNSS accuracy improvement
@Bas_Hamans wrote: I'm pretty new the the ardupilot scene and have finished my first project which is a fishing bait boat. I have used a APM 2.8 with a M8N. Everything is working 100% and I'm very...
View ArticleDisarm procedures for various modes?
@Pedals2Paddles wrote: Can someone verify my understanding of the land/disarm procedures? In stabilize, and acro, you need the throttle stick fully down fully left In alt hold, loiter, and pos hold,...
View ArticleArduCopter flip of dead crash during Autotune (no ESC sync error)
@Viramedia wrote: Hello userMy name is Igor and Im new here in forum, but already ArduCopter user since a few years. Marco Robustini told me that this would be the best place to ask for help regarding...
View ArticleArduRover electric motor throttle and break setting during downhill
@gergo75 wrote: Hello everybody,I have one question, i hope somebody can help me in this.I have one not light weight wehicle, and i attached one arduRover robot. i would like to asking, how do you...
View ArticleFirmware Build Issue
@bbad68 wrote: Hi all. Apologies if this isn't the appropriate category. I've downloaded the PX4 Windows Toolchain (I'm running 64-bit Windows 10), and am attempting to build the firmware as per the...
View ArticleExtensive drift on RTL landing sequence on RC4
@lenorin wrote: Was testing out 3.4 RC4 on the hexa, and twice during an RTL mode the drone would return to hover over home but as soon as it began the vertical descent portion of the mode it would...
View ArticleGps 3D fix but blue led
@lucamax wrote: Hi all,I'm facing a real strange problem. After three hours of regular flights in the past week today after powering up the copter and his Pixhawk clone with Drotek Ublox 8 gps the rgb...
View ArticleClik here to view.
QuadPlane behaves strangely in AUTO with waypoints
@Anthony wrote: My QuadPlane seems to fly well in QSTABILIZE and QLOITER. I haven't tested the transition or fixed-wing yet. So what's below is all in VTOL mode. I tried to load the following mission,...
View Article