Clik here to view.
Autonomous QuadPlane Missions
@GregCovey wrote: Hi, As a prelude to a mapping survey, I have created a simple autonomous mission for my Bix3 QuadPlane using Mission Planner v1.3.39. It is nearly identical to my autonomous mission...
View ArticleThe sensor to measure attitude data in log analysis
@gh_zhang wrote: For Pixhawk Fixed Wing Plane operation, when doing log analysis, the result ATT data representing Roll, Pitch, Yaw angle when operation, from what sensor it measure these attitude...
View ArticleClik here to view.
Need Help/Feedback PID Tuning Large Hexacopter
@RC_Danny wrote: Hi everybody! I've got a large 1280mm hexacopter, Multistar 5008 330Kv motors, 18x5.5 props. I've got it tuned pretty decent in stabilize, but in PosHold (Pixhawk running 3.3) it's...
View Article6m gps not recognized by pixhawk
@acca wrote: HelloI have bought a pixhawk clone named pixhack 2.8.4I'm trying to connect a ublx 6m gps with compas to this flight controller. This gps works fine with apm 2.8 copter 3.2The apm and and...
View ArticleAdded support for new FrSky telemetry protocol varient?
@pauljatherton wrote: Would be keen to get some background info on this enhancement. Background reading somewhere? Posts: 1 Participants: 1 Read full topic
View Article8 Motors are showing up for Motor Test for Y6B in Mission Planner
@Autonomost wrote: I am running a motor test to check the orientation of my Y6B and eight motors show up in mission planner. Which motors should I pay attention to? Posts: 2 Participants: 1 Read full...
View ArticleLoiter drift in 3.4rc3
@doritos wrote: Hi All, I recently upgraded a working 3.3.3 quad to 3.4rc3 and I'm experiencing heavy loiter drift. When hit by light wind (6~7km/h) the quad drift for about 5 meters than suddenly...
View ArticleCH3 RC out delay
@pmshop wrote: It was suggested by a respected member of RC Groups to contact you, the developers, of an Issue I have.Current setup of 2 crafts: 450 QUAD20A 20A Mini Simonk ESCs3DR IRIS motorsPixHawk...
View ArticleRunning the PixHawk without a radio
@dksmall wrote: Well the last thing I tried to do was setup my rover to start without a radio. arming_check changed to 8126 (ignore RC failsafe)fs_action = 0 (disable failsafe) But the rover will not...
View ArticleSkywalker Crashed on RTL done in guided mode "Go to Here" (Arduplane 3.40...
@Rana wrote: Hi,Skywalker Crashed on RTL done in guided mode "Go to Here" (Arduplane 3.40 with APM2.52).Fuselage is damaged, RFD900 also damaged.APM 3.40 Crash during RTL done in Go to Here.zip (931.5...
View ArticleQuadcopter Crash on AC 3.4-rc4
@Frontier wrote: Hello, I am using Arducopter 3.4-rc4 on an AUAV PixRacer board installed on a (clone) S500 frame.The quadcopter uses a uBlox Neo m8n GPS unit and everything is powered via a Matek...
View ArticleClik here to view.
How use a gamepad joystick with Tower 4
@Guiboy wrote: Hey guysI am looking any mean to use a gamepad joystick coupled with this fantastic GCS that is Tower.I have seen people using joystick widgets but I did not get how to install this...
View ArticleClik here to view.
Idea for reducing frustration with compass prearm failures
@tridge wrote: We've been getting an increasing number of reports of frustration with the inconsistent compass prearm errors. A good example is a recent log from Luis:...
View ArticleHelp mission planner settings!
@Jon202 wrote: I am fairly new to quadcopters. Recently, I purchased a quantum nova bnf. I was never able to bind the nova to my receiver so purchased a TX from the dealer. I have programmed the amp...
View ArticleErrors trying to do a simple make px4
@maelito wrote: Hi all, This is my first attempt to programming Ardupilot and i just wanted to do the basics first.On the tutorial...
View ArticleALT HOLD activation causing RAPID CLIMBING 10m ! ( pulse to throtle )
@Petr_Zverina wrote: HEllo , i have little problem with AC 3.3 on Y6B. ( pixhawk ) When i activate althold copter get big pulse to throtle, climb 10m . Then all work ok . This problem coming ONLY in...
View ArticleChanging Arducopter parameters in a mission?
@Pedals2Paddles wrote: Not sure if this belongs here or the Mission Planner section. Maybe both. Are there mission commands that can change Arducopter parameters? For example, I would like to change...
View ArticleClik here to view.
Unrecoverable spin - crash
@bchristal wrote: First off, thanks for the great software!! Plane 3.6 has been rock solid. However, I have found an issue in 3.6 and 3.7. FLying wings can but put in a "death spiral" fairly easily by...
View ArticleROI altitude higher than aircraft altitude?
@Pedals2Paddles wrote: I have ROI with an altitude higher than the aircraft altitude. The gimbal is limited to level to -90 degrees down (it can't pitch up). Will AC just peg the gimbal at it's...
View ArticleRate at which AC initially moves to point at an ROI?
@Pedals2Paddles wrote: What tells AC how fast to yaw and and how fast to pitch the gimbal when it executes a DO_SET_ROI in a mission? It seems to be a rather abrupt move to align the copter yaw and...
View Article