Clik here to view.
No Signal to Motor or Steering Servo (Pixhawk)
@D_S_S wrote: I have tried two configurations for powering my receiver & rudder servo. Neither config controls the ESC or steering servo. Config 1. SBEC powers the rudder servo and receiver. No...
View ArticleClik here to view.
3D Printed Anti Vibration Mount
@GuyMcCaldin wrote: The following was a blog posted to DIY Drones in 2013. I've moved it here to ensure it remains part of the Ardupilot community, should DIYdrones be discontinued in light of 3DR's...
View ArticleHow to cut down messages send by ardupilot?
@DaniAlCri wrote: Hello,I am working with a multiple drones net and i need to try out if i can cut down the number of messages sent to free the bandwidth.For what i know the drone send messages even...
View ArticleClik here to view.
3D Printed Pitot Tube
@GuyMcCaldin wrote: The following was a blog posted to DIY Drones in 2013. I've moved it here to ensure it remains part of the Ardupilot community, should DIY Drones be discontinued in light of 3DR's...
View ArticleClik here to view.
12 Partners Signed up to ArduPilot.org
@billb wrote: After our recent announcement for partners to support the ArduPilot.org project we have had 12 new signees. Click out the partner link to find out more about the benefits to supporting...
View ArticleQuadplane Flying wing
@JetA1 wrote: High Gents, an easy one, but I cant find anywhere:May I use a flying wing setup in Quadplane as well?many txsb.r.Wolfgang Posts: 2 Participants: 2 Read full topic
View ArticleStupid Question
@av8torfl wrote: Hi newbie with another stupid question. I have no problem building a mission that I want my quad to fly and saving it,but how do I tell the quad itself to begin flying the mission?...
View ArticleClik here to view.
Unclear/Fuzzy image on FPV Set up
@J_Pat wrote: Hi Guys,I have been trying to set up a FPV system. I've managed to wire it all up to make sure all components are receiving their correct voltages. I seem to be only receiving a really...
View ArticlePython Program for running Traxxas 3355R ESC
@busbice wrote: First of all thank you if you can help or lead me in the right direction! I've been working on this for the past 3 weeks, everyday and cannot resolve. I am connecting from an RPI to an...
View ArticleMicrobes Transported by ArduPilot Powered Drones Found Safe
@billb wrote: ArdiPilot Plane has been used in testing the safety of transporting microbes in blood and sputum. This just proves how reliable ArduPlane is for commercial applications of drones in the...
View ArticleClik here to view.
Heavy Y6 adventure thru 3.4 RC with Autotune
@Emin_Bu wrote: Hello This is a story with my Y6 and 3.4...Introduction firstSpec:Pixhawk original with ublox M8N GPS(double anti vibration mount,GPS stand 15cm)Y6 foldable carbon frame 820mm mot. to...
View ArticleTakeoff without GPS
@Anis_Koubaa wrote: Hello To takeoff an arducopter using any MAVLink ground station, I noticed that it was necessary to have a 3D fix for the GPS and the copter must be in GUIDED mode. However, this...
View ArticleDiscussion about OpenMP supprot for Linux
@Daniel_Frenzel wrote: What are your thoughts about support of OpenMP for Linux.What comes into my mind is: - Multithreading, as ArduPilot stresses one core already a lot - VectoringI initially, I...
View ArticleTimeout waiting for autoscan/no mavlink device connected
@Alex_Scommo wrote: Just purchased a quanum nova pro, I'm trying to connect it to mission planner but I keep getting this message Timeout waiting for autoscan/no mavlink device connected. The computer...
View ArticleConfigure Mission planner without remote controle
@batsboss wrote: Hello, i have note received my remote controle and i would like to try to fly my hexacopter s550 with mission planner . I have a APM 2.8. Thank you to tell me how i can configure my...
View ArticleClik here to view.
APM stack question, APM vs PX4
@wifiguru10 wrote: So ran across this today. Doesn't APM 3.3/3.4 run native on the hardware? medium.com Why We Chose PX4 (vs APM) as Luci’s Default Firmware Choosing the right flight controller for...
View ArticleFlight Modes, Additional Channel
@av8torfl wrote: I recently hooked up my 6th channel on my quad to my HobbyKing HK T6a V2.It shows up on mission planner radio calibration via my variable #2 dial. My Variable #1dial alreadycontrols...
View ArticleI can not control Yaw of my quad copter via radio stick
@Rolf1 wrote: Hi,I can not control Yaw of my quad copter via radio.I’ m using the controller Pixhawk with the firmware ware 3.3.3. I have following tested - Stabilize Mode- Alt Hold Mode - Loiter Mode...
View ArticleClik here to view.
Arducopter V 2.8 pdf?
@wacked wrote: Is there a PDF to help me wire this up? This is my first time trying this, I need help PLEASE.Thank youTerry Posts: 2 Participants: 2 Read full topic
View ArticleQuad Plane Issues
@garlandk wrote: I have done ESC calibrations, gain tuning, and checked and double checked all of my settings. I am assuming more gain tuning def needs to be done, but I am wondering if it is the...
View Article