Do I need the switch and buzzer for my Px4
@Lat_Long wrote: I'm new to the Pixhawk moving over from APM 2.x. In the getting started guide is says that the switch and Buzzer must be attached. During the set up it didn't seem to matter if they...
View ArticleUsing Channel 6 to switch relay pin - CHDK
@Alex_Backup wrote: I want to use my quadrocopter with a Canon in CHDK-Mode, trigger cam using USB-Cable. My only switch left ist Channel 6. How can i use this channel to switch Relay Pin 9? Iam on...
View ArticleMP load, 403 Forbidden
@Daveb wrote: I saw a post like mine but I could not find the fix, Thanks Dave Posts: 2 Participants: 2 Read full topic
View ArticleClik here to view.
Copter 3.4-rc5 test and logs
@Marcell_Kovacs wrote: Hi, I just finished a small testing with 3.4.-rc5. (take off in stab, switch althold, try stay at one place, land) I had a bit of a problem with altitude hold, the copter was...
View ArticleTower v4.0.0-beta4 tested with Ardicopter 3.4-rc5
@Rod_Davis wrote: Tested Tower beta today with AC3.4-rc5 and had no issues. Tested the following: - vehicle arm & takeoff in guided mode - Follow-me - Dronie - manual flight path capture as...
View ArticleCopter 3.4-rc5 Almost flip, landing detection failure
@doritos wrote: Was running rc3 without big issues, now tried the rc5 and things went very bad. 1) When taking off in AltHold, when you raise the throttle usually motors does a "pulse". This always...
View ArticleWiki ERR found at odroid page
@cala2 wrote: This page at the end refer to the old APM forum to ask questions and the link give an errhttp://ardupilot.org/dev/docs/odroid-via-mavlink.html#Red_Balloon_FinderSorry I'm not have my...
View ArticleClik here to view.
Weed recognition with ballon finder modified code
@cala2 wrote: CC sounds pasionate for who have development knowledge, not my case, It's sounds crazy try to modificate ballon finder code to recognize weeds and, for ex. spray them ? Posts: 1...
View ArticleClik here to view.
Copter-3.4-RC5 Testing - Disarmed during guided takeoff and barometer not...
@rrr6399 wrote: I tested out 3.4 RC5 on my F550 Hexacopter today. The testing went well except for these items: 1.) I had my MOT_THST_HOVER set initially to .2159392 and had MOT_HOVER_LEARN=2 in RC2...
View ArticleClik here to view.
Announcing ArduPlane/Copter GeoFence support in QGroundControl
@DonLakeFlyer wrote: GeoFence support for Copter and Plane ArduPilot firmwares is now available in QGC daily builds. GeoFence user guide:...
View ArticleClik here to view.
How to control more than a relay with radio?
@lucamax wrote: I was able to turn on and off the relay output with pins 54 with radio control . I would like to control a second realy output , pins 55 , with radio control but it does not seems...
View ArticleGyro calibration corrupted by gimbal initialization
@lucamax wrote: There is something I always hated with APM / Pixhawk : it is the initialization of the gimbal . The fact that no valid PWM (I guess) is outputed by the Pixhawk after the battery...
View ArticleWhat does the 'RATE'in the 'DataFlash Logs'mean
@Metello wrote: hi gays! I use the ArduPilot to do some test, now I wonder the rotate speed of the plane .Does the "R",'P',"Y"in the "RATE"of the 'DataFlash Logs'meas that?if that what does the unit...
View ArticleClik here to view.
QuadPlane Conversion of Volantex Ranger EX
@GregCovey wrote: Now that I have had several good flights on my Volantex Ranger EX and have successfully trimmed it out and flown it using APM Plane v3.6.0 with a Pixhawk, I am ready for my QuadPlane...
View ArticleClik here to view.
APM Planner install on linux ubuntu14 - dpkg dependency problem libflite1,...
@jhenry5 wrote: I am trying install APM planner on linux 14.04. I have some dependency issues and not sure how to update the prerequisite files. I am installing APM planner using instructions from :...
View ArticleSonar obstacle avoidance parameters
@ArthurGuy wrote: I have been playing with the sonar avoidance options in steering mode and I had a question about two of the params. One is the rotation time when an obstacle is spotted and the other...
View ArticleNewb and have to write a custom mixer
@PittRBM wrote: First of allI'm new to this whatever community it is called (please tell me)I'm building a synchropter or an intermeshing rotor heli using 2 sets of CCPM.So I pre ordered a Pixhawk 2...
View ArticleAutotune Curiosity
@elkayem wrote: Hi autotune experts... I've run autotune (3.4-rc4) twice over the past two days on a new frame, and received results that are substantially different from each other. I actually have...
View ArticleClik here to view.
Help Diagnosing GPS issue (not a bug report)
@wicked1 wrote: My copter has an issue w/ the GPS I cannot figure out. This isn't beta testing related, so I don't know if this is the best place to ask, but I am running 3.4. Others have been able to...
View ArticleClik here to view.
Ardupilot 2.8 balance out while lifting
@Pilot2016 wrote: Hi, I got my Ardupilot 2.8 and I built my quad on F450 with 1000kv motors. So the configuration is APM 2.8 (ardupilot) A2212//13T 1000kv motors 2200 mAh 11.1 Lipo APM GPS with...
View Article