Onagofly PX4 FMU with Tower App
@themightythor wrote: Hello,I purchased an Onagofly palm sized drone and was please, about the only thing to be pleased about) it contains a PX4 FMU. Upon discovering this, i quickly hopped into...
View ArticleClik here to view.
Show us your orthomosaics
@Tim_D wrote: As the title stats lets see what you have got! Also maybe post a little about your setup and what you use. otho-construct.jpg2000x1566 393 KB ortho-small.jpg1660x1764 1.93 MB...
View ArticleClik here to view.
How to stabilize heading?
@uziak wrote: 20160918_133747292_iOS.jpg1089x1065 276 KB Hi, I am working on my small boat with an APMrover and a pixfalcon. My boat has two paddles on both side and they can be individually...
View ArticleClik here to view.
New plane setup pixhawk
@yak-54 wrote: just trying to setup new planei have 2 servos one in ch1 and the other in ch9 RC9_FUNCTION=18it works fine in manual but if i switch to a flight mode it stops workingi do say its...
View ArticleClik here to view.
APM2.8 "Got param $R0_EXT_STAT
@sieder wrote: Hello Everyone, I just want you to know that I am very new at this. When I start to click connect using mission planner, it got stuck with "Got para $R0_EXT_STAT, any idea what's going...
View ArticleTower v4.0.0-beta4 - Huawei Mediapad M2, 3DR Solo (few minor probs)
@DylanP wrote: G'day Team, Tried the new beta today, had a few minor problems which I'm hoping will be easy fixes (and could potentially be user errors) I fly pretty much exclusively in spline survey...
View ArticleClik here to view.
Max mavlink connections
@pywong wrote: Hello, I'm trying to get this working in Arduplane (3.6.0) but I think it pertains to all Ardupilot flavours so I'll post it here. I'm trying to get a total of 3 Mavlink connections out...
View ArticleStrong yaw when switching from QSTABILIZE to FBWA
@Anthony wrote: Hello, This is a QuadPlane running APM:Plane 3.7.0. I'm trying to transition to fixed-wing. When I switch from QSTABILIZE to FBWA, the forward motor turns on and starts pushing...
View ArticleWaypoint Saving with APM 2.6
@salience wrote: Just upgraded to 3.2.1 with an APM 2.6. With FW 3.1.5 using Mission Planner (~1.3.28) I could save a set of waypoints to my FC via USB and it would remain saved. Now with FW 3.2.1 and...
View ArticlePoor Loiter Performance with Y6
@Autonomost wrote: Hey all, I seem to have plenty of satellites and the HDOP didn't look too bad but I was getting so much drift with loiter. Does anything stick out in the logs? Thanks, 2016-09-18...
View ArticleConnection over mavesp8266 - sonarrange (MB1242) not reported/updated
@ftobi wrote: Hi. Wondered, why my copter doesn't show sonarrange in Mission Planner anymore. Tested a few things and found out that if I connect it via bluetooth or USB the value sonarrange is shown...
View ArticlePixhawk 2.4.8 (clone), AC3.2.1 works, AC3.3.3 Initialising APM when motors...
@zoniiic wrote: This is a Pixhawk 2.4.8, which a clone from Aliexpress, worked well. I'm new to multirotor things, just built my first copter with custom frame few weeks ago, excuse any...
View ArticleArduCopter Current and Voltage Log Data Source
@lzl200102109 wrote: Hello all, I am trying to analyze the current and voltage logs from IRIS+, which uses the ArduCopter firmware v3.3. I have access to the data in MATLAB by reading the CURR...
View ArticleAPM 2.6 DataFlash Log says GPS fail when GPS is actually fine
@Robert_Moore wrote: My GPS (Ublox lea-6m) works fine when I try to loiter and return to launch. APM disagrees and throws failsafes randomly, probably due to GPS and then uses GPS to RTL anyway. How...
View ArticleBuild SITL fail
@jinchengde wrote: Hi all, I meet some build error in SITL Waf: Leaving directory `/home/kent/Git/ardupilot/build/sitl'Build failed -> task in 'objs/AP_GPS' failed (exit status 1): {task 49664400:...
View ArticleSBF GPS seems to be causing Severe scheduler overruns
@mboland wrote: I have been setting up an Octo for some time, a Torrot 1000 size frame with T-Motor U5's.It has flown well with the Pixhawk and UBlox M8N GPS , FW 3.3.3 although with slight yaw...
View ArticleCompassMot Calibration or CompassMot Monitoring?
@R_Q_Robert wrote: Hi All In the Advanced Compass Setup Document , under CompassMot Calibration details it says if magnetic interference is higher than 60% you should try movingyour APM/PX or External...
View ArticleAPM Planner 2.0.23-rc4 broken on Mac OS X 10.12 AC 3.4-rc5
@mboland wrote: I have been working on earlier versions of Mac OS X in the work shop but was having trouble downloading firmware so decided to use the office computer which is now on OS X 10.12...
View ArticleQuestion on TX Mixing and Effect in Auton and Asisted Modes
@jacques_eloff wrote: I have a question on using TX mixing, for example when used to compensate for pitch change on deployment of flaps. When setting up a plane in manual mode, I found that flaps have...
View ArticleConfused about required firmware and sourcecode
@atx80 wrote: Hi guys, I' m up to programm the source code on my Pixhawk (on DIY Y6 frame) but so far im a little confused concerning the firmware. When its connected in mission planner it says in the...
View Article