Flight Plan Issues Mission Planner Version 1.3.41
@WallyGIS wrote: Good day. I just updated Mission Planner. Now when i load a flight plan for aerial photography, the flight time calculation is almost triple the time on the older version 1.3.39 The...
View ArticleCOMPASS_EXTERNAL not saved on reboot (AC3.4-rc5, PixRacer)
@Frontier wrote: After my initial AC3.4-rc4 build skyrocketed and crashed, new parts arrived and the S500 build is again finished. Now, I am running AC3.4-rc5 on my AUAV.co PixRacer and also using MP...
View ArticleAccelerometer calibration before or after mounting
@Remi wrote: Hi!I am putting together my first Arduplane using a pixhawk and a Bix3. I have made several ArduCopters, where I did all the calibrations after assembly. With the bix3 fuselage shape I am...
View ArticleSITL AUTO mode does not work
@ruyi7952 wrote: Control : PixHawk PX4FMUv2firmware: Plane 3.7CGS : 1.3.39 / 1.4.1.3(beta)X-Plane:10.45/10.50/10.51(r1)(Beta) X-Plane 10.45/10.50 , I See GPS3D，But Aircraft location wrong。X-Plane...
View ArticleHaving Control issues
@Robertvanrooyen18 wrote: Hey guys. I'm very new and I just finished my small quadcopter. Was quite interesting trying to get everything run smoothly and I've finally have it all working. The one...
View ArticleFirmware for apm pro 2.6
@iwan wrote: i just installed the last mission planer and this is my first hexa, installation complete then i start to set up my apm pro with "auto" in the upper right corner since there is no arduino...
View ArticleVcc error reported - crash 3.4rc5
@AJack wrote: After solving althold issue took my quad for a spin. Relative good althold, bad loiter (no compassmot). Briefly switch to RTL to get back to stabilize when control was lost resulting in...
View ArticleClik here to view.
Cant get back to 2.9.1 has anyone got the hex file please
@Andy_Edge wrote: my quad seems to drift to the right alot and pos hold is useless since upgrading the firmware can anyone help thanks Posts: 1 Participants: 1 Read full topic
View ArticleWrong distance waypoint in auto mode
@Ihsan_Sansai wrote: i have problem with the my flying wingi'm using- pixhawk ori 3dr with ublox gps ori 3dr- motor emax gt 2826/05- esc 80 amp- battery 5200 4s multistar- prop 12x6- arduplane 3.1.3 i...
View ArticleMixing terrain following with realative altitude waypoints in a mission
@CBaker11 wrote: Mission Planner 1.3.41 Does anyone know if there is a way to create a mission which will switch between terrain following and relative altitude mode? I'd like to be in terrain...
View ArticleClik here to view.
Any difficulties when developing software for drones?
@Mina_Son wrote: Hi, guys! I’m Mina, working at a startup company that develops software and algorithms for drones.I’d like to hear more from you guys in terms of surrounding environments or current...
View ArticleClik here to view.
Analysis error VCC Warn 1.3.41.3
@AJack wrote: Running auto analysis on 1.3.41.3 VCC Warn was issued while on the graph those differences never happened. Could anyone figure out what is this about ? Posts: 1 Participants: 1 Read full...
View ArticleSim_vehicle.py fails to build
@Flyingstoo wrote: Whenever I try to build the sim vehicle the following happens Stuart@Stuart-PC ~/ardupilot/ArduCopter$ sim_vehicle.py -j4 --mapSIM_VEHICLE: StartSIM_VEHICLE: Killing...
View ArticleDisarming in the air
@X1Aero wrote: Which is pretty alarming. I've had this happen on a 960 hex and my 1300 X8. Mission planner announces disarmed during flight, then says armed and keeps flying. The motors never actually...
View ArticleBad altitude hold with 3.4-rc5
@Marcell_Kovacs wrote: Hi, I have strange altutide hold behavior with 3.4-rc5. (genuine pixracer, ZMR250, 4S, 2204 motors, 5045 props, ~20% hover throttle). With sticks at 50%, the copter moves...
View Article3.4 rc5 Wondering why no problem so far
@henrik04 wrote: I think size of aircraft motors props all up weight etc, is important to mention otherwise good or bad has little value...Aircraft is:- Very small quad (550mm {21.65 inches} ) motor...
View ArticleClik here to view.
Pixracer with 3.4-rc5 - good flight!
@Rod_Davis wrote: I tore down and rebuilt a 250 quad and had it's first flight today. Everything went well, including calibrating and flying with oneshot125 enabled, which I could never get working in...
View ArticleClik here to view.
Compass question
@elkayem wrote: I'm running V3.4-rc4 on a BBBMINI. I have both an external compass (HMC5843) and a compass on the MPU9250 inertial sensor (AK8963). The software automatically names the HMC5843 as...
View ArticleUsing APM Planner and microcard
@ricardobk wrote: My Traxxas Aton quadcopter collects data in the form of a .bin file on a microcard. I want to end up with a .kmz file to be viewed in Google Earth and I'm using a Mac to get the job...
View ArticleMP Antenna Tracker screen greyed out
@RANND wrote: I updated to MP 1.3.41 only to find the Optional Hardware - Antenna Tracker screen was greyed out and could not be accessed. MP 1.3.40 had the same problem. MP 1.3.39 had the old Antenna...
View Article