Quantcast
Channel: ArduPilot Discourse - Latest topics
Browsing all 45653 articles
Browse latest View live
↧

MP HUD Terrain Following Active

@RANND wrote: I have successfully used Terrain Following in country varying between 600 and 1400 metres above sea level.Unfortunately, it is all to easy to forget if Terrain has been set in the Flight...

View Article


X8 big copter uncommanded Yaw after 3 minutes, please help to analyze this log

@Sarge001 wrote: 5 6-14-2016 12-42-40 PM.bin.log (1.4 MB)Hello guys,I was flying a X8 octo, and after like 3 minutes it started to rotate around, I could not stop it. It was controllable but, very...

View Article


Altitude jump due to wind

@Oisa wrote: Hi all,I have copter that goes up an down even in the calmest breeze. I was able to replicate this on the bench using a fan. In this setup the copter was not armed, nothing was moving, so...

View Article

Y6B Setup - Upper motors won't spin as fast as lower motors

@Kim-Oliver_Feldhoff wrote: Hello Fellas', I'm stuck at this problem and I'm not sure what to look for. The problem is, that my upper motors never go above 1600 Pwm, while my bottom Motors are pretty...

View Article

Mission planner 1.3.41 survey missing

@gainey2 wrote: Hi I am new to mission planner, I am using 1.3.41 I am trying to do a survey mission , my quad is not connected at the time. I go to polygon setup an area then right click and go to...

View Article


Image may be NSFW.
Clik here to view.

DJI S1000 Motor setup

@mpircher wrote: Hey im converting my S1000 to pixhawk right now. the S1000 looks like this: discourse20161010-100-1he0f0q.jpg1024x818 118 KB pixhawk wants motor inputs like this: so i just logicaly...

View Article

First time beginner setup for a DJI F450 with Pixhawk

@BigAl wrote: I have spent some time searching in the discussion group to see if I could find some guidance on this, but was unsuccessful. I have a DJI F450 kit, and a 3DR Pixhawk, with related...

View Article

How can I make px4-v2 using Arducpter-3.2.1?

@yearnmin wrote: I would like to use Arducopter-3.2.1 for using older coding project. But I encounter an error message. How can I solve it? This is error message. $ Make px4-v2/bin/sh: line 0: cd:...

View Article


My version of onboard oled display for arducopter 3.4

@Alexey_Kozin wrote: hi Alli add new functions for onboard display (now supported for my F4BY and linux version board)it may to be used for pixhawk and other controllers toossd1306 it is small and low...

View Article


Exa first setup issue

@paolo wrote: Hi, I'm setting up an exacopter for the first time, using a Pixhawk autopilot and Hi Flyhyper ESC. I went through all the calibration process with Mission Planner 1.3.41.Once the ESC...

View Article

Amount of throw of control surfaces

@Remi wrote: Hi!As previously stated, I am new to Arduplane, and I am setting ut my Bix3 with Pixhawk. Can someone give me some guidance with connecting the servos to the control surfaces. I don't...

View Article

After autotune, quad uncontrollably rocking on pitch axis in loiter

@metalpiotr wrote: Hi, I performed autotune for the first time in my 450 quad. I flew it around in stabilize mode and it appeared to fly much smoother than the default PIDs, so I accepted the tune....

View Article

TCP Server Connection

@Gerbaum wrote: Hi,Copter is equipped with 4G modem. Because it is behind Carrier NAT I only get a private IP.That's why I have to connect to MP via TCP, and MP has to be TCP server, copter client. Is...

View Article


High Speed Auto Missions

@wicked1 wrote: Has anyone tried doing very fast auto missions w/ their racers? I have been trying to, and it doesn't go as fast in auto, as manual.I have set the "Speed", "speed up", "speed down",...

View Article

Ch3in and ch3out difference

@puhumight wrote: hi; I have a problem related my throttle output.I just bought a fixfalcon and i installed it on my zmr250 frame.The issue is even the throttle is %10 (pwm around 1100) throttle...

View Article


Image may be NSFW.
Clik here to view.

R/C 12 channels CPPM solution for Pixhawk, APM, controllers

@ravid824 wrote: I have many R/C plans and copters that uses the Frsky receivers. All are operated with one radio transmitter. For some of the copters I needed more than 8 channels solution. I wanted...

View Article

How to reduce CPU usage of Mavproxy

@Adolfo_Cobo wrote: Hello to all, I was using Mavproxy in a raspberry pi 2 just to send the telemetry from the pixhawk serial port to the groundstation using UDP and a wifi link. The only other...

View Article


RTL not working properly after firmware update

@jonokimber wrote: Dear All - First post so hoping i've done everything correctly. I own a Quanum Nova quad with APM FC and decided recently to upgrade to FW3.2.1 ahead of trying some auto missions....

View Article

Image may be NSFW.
Clik here to view.

APM Planner 2.0 with Video support

@billb wrote: Quite awhile ago i added video to APM Planner 2.0. I just updated the branch to master 2.0.24 release. It can be download and built from this branch....

View Article

Sampling time of ".log" files?

@AnteroCastro wrote: I need to know what is the Sampling time for adquire the sensors data to store in the log Posts: 1 Participants: 1 Read full topic

View Article
Browsing all 45653 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>