Dataflash Log not recording
@GordonR wrote: Hi All, I am setting up my first Plane with Pixhawk. I "flew" it on the ground with the propeller removed (armed it and started the motor although the airplane did not move), but there...
View ArticleClik here to view.
Wrong orientation on APM Planner 2
@flewis21 wrote: Hi, I have recently purchased a Pix Hawk 2, and upon first system boot up it showed the pixhawk as inverted on the APM Planner artificial horizon. Despite proper calibrating and setup...
View ArticleMultirotor will not arm
@flewis21 wrote: I have had this persisting problem for a bit now, I have completed all calibrations and when I go to arm it it successfully does it in APM Planner 2 but the motors do not start up, it...
View ArticleAPM Planner 2.0 and Mission Planner GPS
@jetson wrote: Hello, I have a project that requires I fly a drone without the aid of GPS. I would like to use APM Planner or Mission Planner to set waypoints for the drone. However, I'm concerned...
View ArticleAPM V3.6.0 error
@BurnPlane wrote: Recently, I download the firmware V3.6 for plane, the tunned parameters was upload to a new pixhawk board while trying to swith the flight mode to Auto, the MP shows RTL mode. Then i...
View ArticleSafety switch disabled - motors do not spin
@anton610 wrote: Hello,i read about the posibility about disabling the safety switch. (BRD_SAFETYENABLE 0)When i have disabled it, the Motors are arming, but not Spinning when i throttle up. (copter...
View ArticleErr: 24-0 & 24-1 + 'copter erratic behaviour
@Graham_Dyer wrote: After some problems with Err 24's and a crash with v3.4.3 I loaded v3.4.4 and it's a lot better. But I still had one 24-0/24-1 event at which point the 'copter went almost out of...
View ArticleMP feature request - extending the radio cal to 16ch
@mike wrote: Michael, Now that we can use 16 channels it would be very helpful for troubleshooting systems to have the extra channels on the calibration page. Even though when you move the extra...
View ArticleAuto turning lights on and off
@anparkinson wrote: What is the easiest way to turn lights on at one waypoint and off at another on my plane with Pixhawk in Auto mode? I have a suitable receiver controlled on/off switch but am not...
View ArticleClik here to view.
GPS glitch and short fly-away with Copter-3.4.4
@rrr6399 wrote: I uploaded Copter 3.4.4 to my Hex and test flew it this morning. I had two GPS dropouts that led to a short fly away where I switched to land quickly and landed safely. I noticed that...
View ArticleHITL Simulation with MP 1.3.40+
@Sagaris wrote: In MP 1.3.40 HITL simulation page was replaced with SITL simulation page. Is HITL simulation with X-Plane or FlightGear abandoned in MP? Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
ArduPilot development report - January 2017
@tridge wrote: Each month the ArduPilot development team hosts a meeting with our partners. At these meetings Randy and I present a short development summary highlighting development that has happened...
View ArticleClik here to view.
DEV call 09 Jan 2017 3pm PST = 09 Jan 2017 2300 UTC
@CraigElder wrote: Copter AC3.5 release preparations. What PRs do we need to get into master before the first release candidate? General* RC_CHANNEL rewrite, Github / issues...
View ArticleMission Planner reloading parameters two times
@droncu63 wrote: Hello I tried in two different computers (win7 and win10) when I click connect button, it loads the parameters and then again tries to load parameters second time immediately without...
View ArticleMission Planner update request
@mike wrote: Michael, Could you put on your list to update the gimbal setup page so the input drop-down has selections for channels above 8. So the mnt_tilt etc can be set to 9,10,11,etc from the...
View ArticleMission Planner bug in gimbal setup page?
@mike wrote: I am having problems getting my new gimbal setup. Pixhawk 3.4.4 firmware Octo coaxialNo gimbal control works Install 3.4.4 quadSafety switch disabledBrd_safety bitmask disabledAll aux...
View ArticleHelicopter SITL simulation in Xplane
@Nikita wrote: Hello everybody. When I had spare I tried to make some simulation of default RC helicopter in Xplane. But he acts so unnatural. . When he tries to make a turn on the point he will...
View ArticleDual servos on Y cable redundancy issues
@Piesang wrote: Good day all. I'm busy with a redundant setup with a APM plane using two servos on each aileron and elevator.The idea is that if one servo burns out, the other one is still functional....
View ArticlePixhawk boots without microsd card
@R_Q_Robert wrote: Hi All I have notice that after uploading AC3.4 , i can boot pixhawk without inserting microsd card .Is it normal. ?? Posts: 2 Participants: 2 Read full topic
View ArticleHow the aerodynamic models of aicrafts used by JSBSIM are created?
@tipehugo wrote: Hi, I would like to do some simulation on a model which is already done : the Rascal. I need to know how the aerodynamic model has been generated. Is this with some software ? which...
View Article