SITL altitude won't increase
@ayertay wrote: I followed the instructions online, and did the exact same thing on windows. I get the map. However, it won't takeoff. It says that takeoff started, but Alt is always 0. Posts: 1...
View ArticleClik here to view.
What is Difference between *.cpp and *.pde in Ardupilot Directory?
@spirit wrote: I want to modifying some code on APM 2.6 I'm using APM 2.6 So I'll use old firmware - ArduCopter 3.2.1-> github.com ArduPilot/ardupilot ardupilot - ArduPlane, ArduCopter, ArduRover...
View ArticleAC3.5RC1 gps/rng/optical flow analys request
@kuspower wrote: I make flight with iris and SF11 + optical flow flying in loiter mode in AC3.5RC1 and standard ek2 settings.During flight I test to go from no gps reception zone to gps zones, also, I...
View ArticleClik here to view.
Air speed not functioning
@pmshop wrote: Air Speed indicator on the left hand side of the HUD is not functioning.This is in Mission Planner 1.3.44.3 Build 1.1.6269.37139 Posts: 1 Participants: 1 Read full topic
View ArticleMeaning of the Abbrevations
@Varun wrote: I am using Pixhawk and was curious to see the datalogs. I was surprised to see that there is no detailed explication of the sensors or variables. I mean, some of them are covered at the...
View ArticleCalibrating compass confusion
@GordonR wrote: I have my Pixhawk mounted transversely pointing to the right. My external compass is mounted pointing straight ahead to the front of the aircraft. The instructions, both in Advanced...
View ArticleNo SBUS signal after update from 3.4.4 to 3.4.5
@re4mat0r wrote: Hi. After updating to 3.4.5 RC doesn't work anymore. I use Futaba 14SG. It worked with 3.4.4. When I downgrade to 3.3.3, it also works, but I need 3.4. In calibration screen of...
View ArticleV3.5 rc1 uncontrolled flight
@rbachtell wrote: After dozens of perfectly stable flights my 960 hex decided to have it's way with me. I went out to the flying field to test telemetry range with TX1 (not the first time with TX1)....
View ArticleThe list of available modes in MAVProxy
@Pavel_Bobov wrote: Where does MAVProxy get the list of available modes? AUTO> ('Available modes: ', ['AUTO', 'GUIDED', 'MANUAL', 'LEARNING', 'RTL', 'INITIALISING', 'HOLD', 'STEERING']) ......
View ArticleNAV_SET_YAW_SPEED Question
@hdmathias wrote: Hi everyone. Today I began experimenting with the new NAV_SET_YAW_SPEED command. After a few tries (and software updates) I got it to work. Well, more or less. My setup is an onboard...
View ArticleClik here to view.
My idea for GSOC
@khwu wrote: What I am doing I am Kang-Hua. I am currently a master student studying at San Jose State University majoring software engineer. Because of a recent project, I found ArduPilot community...
View ArticlePoshold problem 3.4.5
@ua0ldk wrote: Hi all. I have strange holding of position (Poshold mode) of my quad in windy weather today.This mode is similar althold. Other modes - Stab, Althold, Loiter are correct in 3.4.5. FC is...
View ArticleNightmare compass calibration
@lucamax wrote: I'm facing big problems of compass calibration with two Pixhawk boards from Mrobotics and 3.4.5 firmware.Compass are two M8N Gps with integrated compass (HMC5983) from Drotek and two...
View ArticleBebop 2 video stream
@Gabuland wrote: Hello,I'm new in the drone environment and I bought a bebop 2 drone a few month ago. I decided to take my drone experience to the next level by joining the ArDupilot community. I've...
View ArticlePlane Crash logs 3.7.1
@yak-54 wrote: Hi all i took a new plane out for its maiden well it was flying great up to ten mins into the flight i saw it glitch so i started to turn for a landing asap never made it.it just sing...
View ArticleTranslate ptich/roll angle to PWM output for servos?
@mauritzg wrote: Hi Is there a way to have the pitch and roll angle translate/map to PWM outputs for servo angle? I would like to have two servos turn directly proportional to my Quads pitch and roll...
View ArticleBad AHRS, pos vert&horz variance
@puhumight wrote: Hi all,i just bought a pixfalcon and entered the pixhawk world.I am us'ng copter 3.4.5 and during configuration i faced errors related to Bad AHRS.In MP everthing is seems allright...
View ArticleTiny RTK integraton
@funfrancis wrote: Hi Have anybody used the TINY RTK with RTK have some issues and would be glad if it could be solved For the standalone test, I believe you did the steps here:...
View ArticleClik here to view.
Disarm: GPS Speed Error
@flyingw wrote: Hello all, I am getting this error: What does it mean? I want to demo the setup and need to be able to arm indoors without GPS. How can I disable the pre-arm check for this condition?...
View ArticleClik here to view.
Getting Params 12 Dialog Box
@ardisd wrote: I have noticed that a Getting Params 12 Dialog Box does not appear to be working on the latest version of mission planner I can cancel the message and everything works as normal. Thanks...
View Article