Disabled Pre-Arm Checks, but still cannot arm because of No 3D Fix
@flyingw wrote: Is there a way to be able to arm when the GPS is not used? I want to demonstrate Mission Planner and ArduCopter indoors where I will not get a GPS fix. I want to ARM and DISARM so...
View ArticlePixRacer with ESP8266 WiFi
@dkemxr wrote: I have a PixRacer on a Rover running 3.1.1 and as with the current stable version (or beta for that matter) of Copter there is an issue with the ESP8266 WiFi radio loading parameters....
View ArticleHelicopter Default Params
@ChrisOlson wrote: I don't know if this has been asked before. But is there any way to have a different set of default params for helicopters vs multi-rotors? As an example, and one that the Trad Heli...
View ArticleConfused about FENCE_ACTION
@Anthony_Short wrote: Hi everyone. I'm inching towards the first flight of my first ArduCopter build. It's a basic flamewheel 450 clone with a 3DR Pixhawk running ArudCopter 3.4.5. I've been looking...
View ArticleMissionPlanner GitHub repository broken?
@knud_dyring wrote: Hi I have been trying to clone the MissionPlanner code from https://github.com/ArduPilot/MissionPlanner. However after cloning the code, some files will show as changed directly...
View ArticleCan not get rid of the compass variance error
@Flavio wrote: Hello Guys!I'm setting up my plane and I keep getting the message that there is a high compass variance, as the EFK seem to be very high. Could this be because the GPS is very close to...
View ArticlePixracer - PX4Flow issue
@Guillaume33 wrote: Hi all,I'm Guillaume from Bordeaux, working on uav flight without GPS.I'm trying to set up PX4Flow module on a little uav controlled by a Pixracer. Problem is that i've no values...
View ArticleClik here to view.
Guided mode with indoor optical flow only
@chobitsfan wrote: Hello hardware: px4flow & lightware sf/10a , indoorI try to use set_position_target_local_ned to set velocity to control copter from companion computer. I have successfully took...
View ArticleWP Speed Increased in Auto Flt Mode
@Sully wrote: I am trying to achieve a much higher speed than default when moving from WP to WP. Going through many of the Parameters I am not getting anywhere. I have increased WPNAV_SPEED_UP to 1000...
View ArticleReal take off rate angle different from the one that was set up
@Flavio wrote: Hello guys!I set up the angle for the take off rate to be 30° on my blended wing uav, but when I take off the angle seems to be lower than that, what could be the problem? Thanks in...
View ArticleCopying parameters to new autopilot
@Flavio wrote: Hi everyone!I have set up an autopilot and my quadcopter flies perfectly, but I have recently burned the entry port of the autopilot so I need to change it. Is there anything that I...
View ArticleTrims change when enable joystick
@focus6513 wrote: When I enable the Logitech Pro 3d on mission planer my trims in roll and pitch changes.How can I set the trims to be the same as rc transmitter? Posts: 1 Participants: 1 Read full...
View ArticleClik here to view.
RTK Issues with MP beta
@mtbsteve wrote: Still having issues to understand what the RTK Inject in MP really does.I am using an m8p base with the latest HPG 1.3 fw and u-center 8.24 connected in parallel to MP 1.3.44.3...
View ArticleMission planner language
@Costy wrote: Hello everyone,I will need some help to change the language in mission planner . My computer setting are in italian. I install MP and i change the language in the planner window in...
View ArticleCrash During Autotune
@Enoc_Sanz_Ablanedo wrote: It´s a quad (Tarot 650) with a large props (17''), slow motors (390kV), X frame. With defaults PIDS it start flying well but after some strong roll or pitch it start to...
View ArticlePID settings do not go below some minimum
@re4mat0r wrote: Hi. I am testing my hexa copter (APM Copter 3.4.5) mounted on table. For testing purposes I lower stabilize Ps to zero. The problem is I can not lower them below 3.0 anymore. I was...
View ArticleIs 3.4.5 limiting PIDs minimum values?
@re4mat0r wrote: Hi. I cannot go below 3 on Stabilize Ps. Is it APMs limitation or Mission Planners? I need to go to 0 for testing purposes. Thanks,Roman Posts: 1 Participants: 1 Read full topic
View ArticleRover not steering in AUTO mode
@amulya123 wrote: Hello Everyone,Acutally, I am using mission planner 1.3.44 and I have ArduPilot 2.5. I can steer the rover in the manual mode. When I switch to the AUTO mode it still runs however,...
View ArticlePlease help! Huge roll oscillation on my new miniquad
@nghiajenius-dev wrote: I've just built a miniquad with DALRC 265 frame, Emax motor 2205s, and littlebee 30a blheli, DAL bullnose 5 inch prop. I use Pixhawk 2 as a flight controller, PID as default.I...
View ArticleProspective GSOC student
@StellarMind wrote: Hi guys! My name is Sahil Tapiawala, I am a student of BITS Pilani, India currently doing my bachelor's thesis at Singapore University of Technology and Design in the bio-inspired...
View Article