Quantcast
Channel: ArduPilot Discourse - Latest topics
Browsing all 46846 articles
Browse latest View live

Module d’alimentation GM V1.0

Bonjour tout le monde, j’ai ce module d’alimentation GM V1.0 je n’arrive pas à le configurer sous Mission planner. J’ai toujours la batterie en défaut. Avez vous une idée ? Merci beaucoup pour votre...

View Article


Issue with acro mode

I have a Heewing T2 with Holybro Kakute H743-Wing controller running Arduplane 4.6. The airplane flies good in fbwa and fbwb. When I switch to acro mode everything is ok. I then raise the nose a few...

View Article


Copter Spins up props when transition to idle mode after landing

After the drone lands the props all spin up to 50% for about 0.5 sec just before dropping the props to idle speed. I am using a radio in Pos Hold mode and allowing the copter to land by reducing...

View Article

Customized Ardupilot firmware by editing the source code

I want to edit the source code of the ardupilot firmware such that if an RC channel is assigned to let say CH_7, it will enable a flight mode which will be uninterrupted by any other rc switch,...

View Article

Full Chip Erase

Hi guys I’m planning to do full Chip Erase in Pixhawk Cube Orange Plus. Can anyone guide me how to do full Chip Erase 1 post - 1 participant Read full topic

View Article


No telemetry with yaapu when elrs in mavlink mode

Hi, I’m trying to setup yaapu with latest ELRS in mavlink mode, the problem that I get no telemetry stream until I connect GCS, obviously it set SRx_* with REQUEST_DATA_STREAM but it’s not clear who...

View Article

Image may be NSFW.
Clik here to view.

Endless 'probing for SBF' messages

I am trying to setup a holybro Mosaic-H on a Cubepilot Orange+, but I am not having any joy! I followed the instructions on this setup page, but the main LED is not coming on, and mission planner is...

View Article

Yaw Control Issue During VTOL Landing in Windy Conditions

Hi everyone, I had trouble landing my VTOL in windy conditions. My VTOL with Q_Weathervane s enabled, I switched to QHover and * tried to manually control yaw to avoid obstacles and align my view, but...

View Article


AttitudeTarget command

I want to use AttitudeTarget command to control my drone autonomously. I am using a PID controller for roll , pitch, yaw to achieve my desired values(my desired roll, pitch, yaw is 0,0,0). From the...

View Article


Help Troubleshooting a controller/ Mission planner

Hi, I’m working on a project that uses Drone engage to control a ground “rover” via 4G. My rover has a Mateksys F405 wing V2 FC running ardupilot. I know this is not directly Mission planner- But, I...

View Article

Best way to send commands to lua script

Hi, I’m using the built-in Simulation (Plane) in Mission Planner and running on windows. I’m curious if anyone has had any luck sending MAVLink commands that are accessible to a lua script. For...

View Article

ArduSoar V2 - TBS Import Tariffs

Topic: TBS Import Tariffs Proposal type: Hardware , Software , Other : _________________ Description TBS shipped me some parts for my next version of the ArduSoar vehicle, but there were import...

View Article

Image may be NSFW.
Clik here to view.

Wobbling drone - at low thrust

Hi! I have built a drone. Speedybee F405 V4, 60A ESC, 4S1P battery pack (21700 EVE 40PL, 70Amp cells). I have strapped the drone to a heavy piece of wood, to avoid flip-over, fly-away … It’s an...

View Article


ArduPilot Parameters are Taking Out of Range Values

Hi, I am trying out setting ardupilot parameters in SITL with mavproxy. I am setting parameter values for RC1_TRIM. I see that I can set floating values to the parameter though it is supposed to be an...

View Article

PCB design files without buried vias

I would like to make my own board (order PCB, components, and solder myself), but I only found one “open hardware” board that actually had any PCB design files (Hardware/FMUv3_REV_D at master ·...

View Article


Image may be NSFW.
Clik here to view.

Taking our AMD R120 Mower to the next level

New Member here, but not new to things Radio Controlled, Pixhawk and autonomous flying machines. Hoping for advice along the way and as a build log as this project progresses. I’m working on...

View Article

ELRS Backpack wifi connection

Hi folk I have been using ExpressLRS Airport for telemetry for a year now, RC on 2.4 GHz and Airport on 900MHz. Everything works great except that connecting the telemetry takes a few minutes. When I...

View Article


Quadcopter video feed starts breaking bad as soon as I turn on my radio...

Greeting I have been trying to troubleshoot this problems for 3 days. The problem is the video feed from my 5.8 ghz transmitter starts breaking badly to the point where you can not fly at all. My...

View Article

How do I automatically turn off the engine kill switch whenever I switch the...

Hello everyone, Our team has developed a VTOL UAV with a maximum takeoff weight (MTOW) of 25 kg that uses a gasoline engine for forward thrust. After taking off in QLOITER mode, we transition to FBWA...

View Article

Multiple RC Receivers on Matek H743 V3 – Setting Primary RCIN

Hi everyone, I’m trying to set up multiple RC receivers on a Matek H743 V3 flight controller. One of the receivers is connected to RX6 (used as RCIN), and another one is connected to a different...

View Article
Browsing all 46846 articles
Browse latest View live