Clik here to view.
MAVLink to HoTT telemetry converter for Graupner RC users
@zdv770 wrote: New version of mavlink to hott telemetry converter is ready for beta-testing and usage.It was attempt to take most from both MAVLink and HoTT. It emulates all known sensor modules from...
View ArticleClik here to view.
EKF and CPU error
@timvand wrote: Having an issue with a rig that is flying erratically. What is the meaning of the error, err:cpu-1, err:cpu-0 160621_10.bin.jpg1189x493 101 KB 160621_11.bin.jpg1189x754 169 KB And what...
View ArticleMinumOSD not displaying 3dfix and sats
@Barry_Bolton wrote: Good day everyone. Had to change my GPS to serial 4/5 as its seems Serial 3 port is busted. Everything works fine and getting good GPS signal as per Mission planner but sine the...
View ArticleClik here to view.
Plane dives when transitioning to RTL
@bchristal wrote: Arduplane 3.6Flying wing Seems like this issue has been around for a while, but I've never found a cause or fix. Just built a new plane. Flies perfect - except when it transitions to...
View ArticleQuadplane frame types
@lifepac wrote: Does quadplane support a tail-sitter type frame. The video below is not mine, just an example. I'm surprised these are not the standard type of quadplanes. In the quadplane docs I see...
View ArticleCamera Gimbal Issues
@ripfree wrote: I'm having trouble getting the PAN function on my 2 axis FPV camera to work with my Px4. Everything else is working great....I've flown some long missions. I have ch6 on the RC...
View ArticleClik here to view.
Sonar air boat working fine
@gvr63 wrote: P1210643.JPG1200x820 559 KB Hello sonar boat designers My new sonar air boat project is nearly finished. The boat is build from an old bait boat. The brains are a pixhawk controller. The...
View ArticleClik here to view.
What if ArduCopter/ArduPlane does not occur in my Arduino's Sketchbook?
@lbc45123 wrote: I followed the instructions on "How to Build Ardupilot with Arduino", but in the end, my Arduino looks like this: C3CB7A7E-A80F-46E1-BE95-6B9BFB7EB7AA.png1122x578 278 KB whereas it...
View ArticleGyro Crawl help
@netptl39 wrote: Hi all, I am having a bad gyro crawl on one of my pixhawks running v3.5 and v3.6. I have up and downgraded several times the firmware and still have the issue. Sometimes it forgets to...
View ArticlePixhawk Lite – how can I use Servos?
@Don_Sebastian wrote: A Pixhawk Lite has only 8 RC Out ports.Is it possible to realize a camera Trigger via servo?Can i configure one RC-OUT so that it should not use 400Hz? A large Pixhawk would not...
View ArticleFalse low battery warning
@courierdude wrote: Hi all I'm having a problem with the low battery warning function on my Pixhawk. On the HUD screen in Mission Planner, at the bottom where it shows the battery voltage and amps, it...
View ArticleClik here to view.
Double driver source code for Toshiba RGB LED
@jeroent wrote: Hi. I don't have access to the development forum yet. As the current Toshiba RGB LED driver in the Pixhawk (V2) is end of life I have added support for a TI LED driver in the source...
View Article6 Modes over 2 Switches - Flysky FS-i6 Tx
@Albi wrote: Hi,I'm having some trouble setting my Tx to produce the correct PWM values needed to select 6 flight modes using 2 switches. I'm using a Flysky FS-i6.I've tried following this tutorial...
View ArticleCamera gimbal pan acting like switch channel instead of analog channel
@ripfree wrote: I'm having trouble getting the PAN function on my 2 axis FPV camera to work with my Pixhawk. Everything else is working great....I've flown some long missions. I have ch6 on the RC...
View ArticleClik here to view.
Differential thrust for twin engines
@wkf94025 wrote: Does ArduPlane support differential thrust for twins? I searched the Plane category and didn't see anything. A bunch of us flying MyTwinDream's are starting to talk about it. Not...
View ArticleUpgrade to 3.6, no more airspeed sensor & plane dips left in FBWB/A
@raphh wrote: Hello, Helping a friend with a Pixhawk clone (rtfhawk). Upgraded to 3.6, now airspeed sensor is stuck at 5mph and does not move. pin is set to 65, and the airspeed + external compass on...
View ArticleManaging multiple versions of MP in Windows?
@wkf94025 wrote: I could use a little bit of guidance on managing multiple versions of Mission Planner on my Windows 7 environment. At a minimum, I would like to have latest version (currently 1.3.37)...
View ArticleProblem with LCD Display FLD-02 and Telemetry Pixhawk
@jfh900 wrote: I have the following material: FrSky D8R-II Plus 2.4Ghz 8CH ACCST Receiver TelemeteryFrSky LCD Telemetry Display FLD-02FrSky Receiver Upgrade Lite FUL-1Pixhawk PX4 2.4.6 Flight...
View ArticleI2C LED controller - where to get started on driver
@CoreyOsgood wrote: Hi All, I've got a PX4Lite inside a Cheerson CX-20, and I want more/better LED indicators than just a single RGB LED, and also I wanted to make the stock rear lights work as...
View ArticleClik here to view.
Can a PixHawk work in a real airplane?
@CharliEcho wrote: Greetings everyone. Noob alert!! I'm new to this forum and VERY new to this subject matter so please forgive my lack of knowledge. Feels right now like I am drinking from a fire...
View Article