Pixhawk Firmware does not boot
@simonr wrote: Hi, I am using a pixhawk, which does not boot.I am still able to upload a new firmware to it, but the problem stays the same.It is similar to the one described in this post:...
View ArticlePrecision landing with IR -lock
@Marcos wrote: HiI write in Spanish because my english is very bad. Sorry. A ver si me podéis echar una mano porque no hay manera.... Primero cuento lo que he ido haciendoTengo el Pixmon con versión...
View ArticleUpdate PX4Flow's transmittbuffer for further communication (i2c) with pixhawk
@forscience1337kaju wrote: Hey guys, this is a bit complicated to explain. I tried several times to extend the transmittbuffer (update_TX_buffer) for I2C.Therefore i added like a dummy variable to the...
View ArticleUnable to get a single .BIN log stored on SD
@Andre-K wrote: Pixhawk with AP3.5.3 , arming check disabled, logging bitmask at 65535 - SD formatted.I can boot it, arm, it - it will create APM folder , and mixer file - but it will not write a .BIN...
View ArticleLoiter mode with optical flow crashing into the wall
@sudotong wrote: Hi all, I'm Sam from MIT UAV Team and we're working on a competition where we need to fly inside autonomously. We're using the 3DR Solo which has a pixhawk 2 onboard, and we're using...
View ArticleArduCopter 3.4 status
@waterlooalex wrote: Hi, I feel a bit in the dark, whats the status of 3.4, is it released? If not, is it (almost) ready for production use? I'm doing a bunch of work trying to get a 3DR Solo flying...
View ArticleAutotune - can't find AUTOTUNE_AXES parameter
@lordmakaron wrote: Hi, I did autotune about half a year ago. Now i read here: http://ardupilot.org/copter/docs/autotune.html?highlight=autotune that with 3.3v it can also tune PID for yaw. So I tried...
View ArticleDrone from Ground to Space and Back - Possible?
@dipama wrote: Hey everyone, I've been into drones for a while and have piloted a few through my freshman year in college, but I'm eager to build a drone myself. Are there examples of how to build a...
View ArticleArdupilot simulator not working on new version of Ubuntu
@Imran_Khan wrote: I just recently upgraded my ubuntu to new version that is 16.04 and now i am getting errors in starting simulation mission. Is this only compatible with early versions or there is...
View ArticleClik here to view.
Xplane 10 setup for pixhawk
@ath356 wrote: Hello everyone and thank you for your time Im having trouble setting up Pixhawk for simulation with xplane 10, im not shure what you recommend and what's better through your experience,...
View ArticleThrottle run away on minimal throttle input
@pmusto wrote: Hello,I am hoping someone can help as I am completely stumped! I have self-built a hexacopter with the following specs:Emax MT2216- 810KV motorsSpider 20A ESCs re-flashed with BLHeli...
View ArticleIs there a GPS issue with 3.3.3?
@MBeaubien wrote: I began having loss of GPS lock since updating to 3.3.3, is there a known issue with it? It's happened several times at home and other locations where pilots flying with other flight...
View ArticleWhen exactly does EKF revert to DCM?
@todd wrote: We're trying to debug some funny attitude behavior while flying in Attitude Mode. With EKF_FALLBACK set to 1, at what point does it switch from using the EKF filter to the DCM: a) As soon...
View ArticlePWM not changing in mixes for flight modes (Turnigy 9X)
@virgodave61 wrote: Im using a Turnigy 9X with stock firmware and PPM mode between the receiver and APM 3.1.When I change the range in the mixes for the switches nothing changes when I look at the...
View ArticleClik here to view.
Quad Plane - RC input, out discrepancy
@Kyomo_Jung wrote: Hi The below pictures shows RC input and out from telemetry logs.What I don't understand why RC input shows only channel 8 traveled between 982 and 2006 even though all of RC...
View ArticleThree position camera control
@rbreuss wrote: Im operating UAV plane, controlled by Pixhawk for aerial imagery purpose. Pixhawk is controlling camera shutter by one channel. But this camera control has just two positions - shutter...
View ArticlePython code standard
@khancyr wrote: Hi , In PR https://github.com/ArduPilot/ardupilot/pull/4092 we raised the question about using a code standard for python. I would like to propose pep8 as standard .It is pretty well...
View ArticleFirmware update
@dron3n00b wrote: The latest time I connected the pixhawk to the laptop with the mission planner SW, I was prompted that there was a firmware update. I have not updated the firmware yet, but was...
View ArticleServo connections for our fixed wing drone
@dron3n00b wrote: My team and I are having some difficulty in determining a correct way to connect the servos to the pixhawk. FYI, we are using the UAV-3000 airframe as our drone:...
View ArticlePixhawk build motor not spinning with the others after successfull auto tune
@Pimpsn00ky wrote: I completed a new build with pixhawk. everything went smoothly. during first spin up followed the directions watched some youtube and successfully completed the all in one...
View Article