Proposal for Bounty for Easy-to-use ROS images for RPI3
@rmackay9 wrote: Topic:Bounty for Easy-to-use ROS images for RPI3 Proposal type: SoftwarePlanned amount $$ (USD): $500 bounty Description: ArduPilot (in particular Copter) supports ROS via mavros but...
View ArticleClik here to view.
Gee I wonder who he is talking about
@CraigElder wrote: www.forbes.com Watch Founder And 'Evil Genius' Ian Cinnamon Build A Drone In Minutes Entrepreneur Ian Cinnamon and HP CTO Shane Wall talked about the future -- and built a drone at...
View ArticleHow to connect via Bluetooth Low Energy Tower
@spynokia wrote: Members seeking the guidance of the great God, thank you！ Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Implied RTL goes to 160m after mission completes
@Hein_Du_Plessis wrote: I have my RTL home set to 100m, and my mission is also at 100m, however, once the last waypoint has been reached (46) my plane goes in in RTL and then climbs sharply to 160,...
View ArticleDirect SBUS Output on Ardupilot-Linux ports
@james_pattison wrote: Topic: Direct SBUS Output on Ardupilot-Linux ports Proposal type: Hardware [ ] , Software [x ] , Other [ ] : _________________ Description:Implementing a 100kb/s inverted uart...
View ArticleReference Designs
@james_pattison wrote: Topic: Reference Designs Proposal type: Hardware [x ] , Software [ ] , Other [ ] : _________________ Description: The designs/components in the wiki are quite dated, and often...
View ArticleClik here to view.
PID control loop, question about giro drift and acc noise
@pixhawkstm32 wrote: Hi guys, I want to understand more about the control loop design of the ardupilot or in general. Maybe this link here is a good example:...
View ArticleMission Planner cant connect to Mega 2560 Help needed "Solution found see below"
@flyoz wrote: Hi everyone. I hope someone can help.I can get everything to work on my in 10 laptop butI am trying to run Mission planner on win7 32bit Business version op system laptobwithout luck.I...
View ArticleRaspberry Pi not sending information to Pixhawk
@TestAccount wrote: Hi, I have a Pixhawk connected to a Raspberry Pi 3 as per this article: http://ardupilot.org/dev/docs/raspberry-pi-via-mavlink.html via the Telem2 port. Everything has been set up,...
View ArticleBuilding Example Sketches
@hudemirc wrote: Hello I was trying to follow the steps on the website below http://ardupilot.org/dev/docs/learning-ardupilot-the-example-sketches.html However i am facing the problem that...
View ArticleHelp binding/communicating APM 2.6 to DX6 using PPM
@AlexL wrote: Hello! I am getting into drone building, and to start with a bought a used DIY drone from a drone store. It turns out their staff person familiar with APM left the company so they are...
View ArticleLooking for a 24v HV BEC
@X1Aero wrote: Does anything rated higher than 12v even exist? I've got a Castle Creations CC Pro, 12.5 and 11amps output hooked up to a 8s pack. I need about 50% more wattage. So either I higher amp...
View ArticleLoiter can not forward straightly
@yihao_wang wrote: Hi Developer I flied my copter with 3.4,everythings are perfect. The drone can keep the position perfectly in loiter mode.But when i forword(use pitch channel only) my copter with...
View ArticleClik here to view.
Panorama Mission using do_jump command
@Alex77 wrote: Dear community, i'm trying to set up a panorama function for a multicopter. I'd like to use Missionplanner and 30deg steps clockwise using the jump command. I could then define a...
View ArticleCopter Survey Mission // turn into new gridline more smoothly
@Alex77 wrote: Dear community, in a survey mission my Hexa is following the gridlines quite tight, which is a nice performance. But when it comes to turning at the end of each gridline it is a hard...
View ArticleClik here to view.
SidePilot - iOS Groundstation for Arducopter and PX4
@Tommy-b-10 wrote: Hi! Version 1.1 was just released of SidePilot, the iOS Groundstation app for Arducopter and PX4 (formerly called iMavlink). discourse20161002-100-eio1vs.jpg360x640 41.8 KB New...
View ArticlePlane 3.7 Q parameter possible bug
@darrell wrote: When I set Q_MOT_SPIN to a value high enough to spin my motors on arming only motor #1 (front right) spins. I would expect all four motors to spin like they do in copter. Posts: 1...
View ArticleRC6 m8n "GPS 1 failing configuration checks"
@HITMAnsOFT wrote: Hello, I'm getting the following prearm errors with Copter 3.4 RC6:[MAV 001:1] PreArm: GPS 1 failing configuration checks [MAV 001:1] GPS 1: u-blox raw rate configuration 0x100 The...
View ArticleCould PID tuning be implemented in on-demand way?
@dipspb wrote: Hello, Currently I can see two ways for APM:Copter to tune PIDs in mid air: via CH6 and by using autotune feature. What if it could be implemented to work in on-demand way? Imagine...
View ArticleWhy i loss throtle control when i switch to altitude hold mode irrespective...
@umarufx wrote: Hello I am using ardupulot2.8 borad with latest firmware v3.3,i have very good control on stablize mode.but when i switch apm to altitute hold mode it maintain its alt position and i...
View Article