Auto Mission or Script
@ardisd wrote: I it possible to run a series of commands like an Auto Mission but without the GPS Cordinates. for example fly forward 20m, yaw 26 degress, decend to 10m etc. I would like to run a this...
View ArticleArduPilot Antenna Tracker
@GregCovey wrote: There are several variants of the Antenna Tracker so I decided to document my AT build here which follows the ArduPilot Antenna Tracker design. This version was originally designed...
View ArticleUASUSA use caution
@CraigElder wrote: Since this is an open source project and we all benefit by being open it is time to be open on an unpleasant topic too. I currently have nearly $20,000 in unpaid invoices going back...
View ArticleConverting Bin files from PixHawk to CSV?
@Mike_Jones wrote: I am looking for a python script or anything at this point for a method to parse the data from a pixhawk that was flashed with mission planner firmware.(That is the extent I know of...
View ArticleCompass set up with Ardupilot is a Fiasco
@Marc_Dornan wrote: Ok, the title of my post was designed to be provocative! It does not reflect my feelings about Ardupilot though. I have been using Ardupilot for years but only recently had the...
View ArticleFWBA - No Left Turn?
@paulham wrote: I was flying my wing today (running pixhawk and APM Plane 3.6.0) and I noticed that in FBWA mode I couldnt turn LEFT. Right turn was working. I switched to stabilise and I could turn...
View ArticleMavlink Command #70 from LabVIEW
@AstroTobi wrote: Hello, i have to send the Mavlink Command #70 to a Pixhawk.My created Message looks like this:Start of Frame 254PL length 18Packet Seq. 0-255Device ID 253Comp. ID 0Message ID...
View ArticleArduPilot with Iridium RockBlock Modem
@BobbyWatts wrote: Hello all, Looking for a solid autopilot that will allow me to control my aircraft beyond visual line of sight (Yes, I know... illegal here in the USA but this is for relief efforts...
View ArticleClik here to view.
How to use channel 9 and 10 for gimbal control?
@Guiboy wrote: I would like to set my RC channel 9 and 10 respectively for tilt and roll of my gimbalI can do it using the gimbal configuration tool of Mission Planner that allows me to select both...
View ArticleMavlink Routing
@khancyr wrote: Hi, is there a way to disable mavlink routing from a port ? I got two drone with pixhawk and CC. CC use mavros to send order to pixhawk via serial (telem2), telem 1 is used by 3dr...
View ArticleClik here to view.
MinimOSD v1.1 connections/cables
@legwind wrote: Hi all,My first post here! Yay! Recently I purchased the HKPilot Mega 2.7 Master Set with OSD, LEA-6H GPS, Power module, Telemetry Radio (915M) from the Hobbyking AU warehouseI've been...
View ArticleIssues Compensating for Barometer Drift Using GND_ALT_OFFSET
@rrr6399 wrote: Has anybody used GND_ALT_OFFSET using the altitude from a ground based Pixhawk to correct the altitude of a copter? I'm seeing poor results with it over longer durations. I'm updating...
View ArticlePixhawk Motors Keep Shutting down
@propflux01 wrote: I don't know if I am in the right place or not, This is my first post here, and my first experience with Pixhawk. I posted on another forum and was directed here. the following is...
View ArticleClik here to view.
Not stable take off in stabilize mode but smooth flight
@Ivosch wrote: Hello,I have almost everytime small issue during take off in stabilize mode @pixhawk and arducopter 3.3. When hexacopter is on the ground and I'm increasing throttle, drone starts to...
View ArticleBBBmini: Hardware tests fail
@steveb1475 wrote: Hey all, I'm still having problems getting this thing going. Both hardware tests for the IMU and Baro seem to be failing: debian@beaglebone:~/ardupilot$ cp build/bbbmini/examples/*...
View ArticlePrecision Landing/IR lock for ArduPlane
@simo10 wrote: Hello guys, I'm new to this great community. I'm working on a project that requires precision landing for fixed wing planes. Similar to the function already implemented in the...
View ArticleRover Brake Servo Control in Auto
@PDACTMike wrote: I've successfully built a full sized rover (as in 1998 Dodge Ram, for use in fields). However, I currently only have Throttle and steering, both servos, but have need some guidance...
View ArticleUnable to change Ardurover Firmware in Mission Planner
@jghielme wrote: Using an APM 2 Mission Planner 1.3.41Using version v2.51 beta Tried to change to version 3.0.1 Disconnected APM - Selected Initial Setup - Install Firmware - selected ArduRover...
View ArticleClik here to view.
Can't download previous firmware (AT 0.8.0)
@lospalos wrote: Hello guys,I want to utilize old APM1(2560) board for AntennaTracker and want to upload there FW of version 0.8.0 via MissionPlanner. When I hit "Load previous firmware" after...
View ArticleCant get copter to orbit POI
@Gun-Jam wrote: Hello I have an x8. using mission planner I set a point of interest and a home location and send the mission to the copter. According to the copter wiki when a POI is placed on the map...
View Article