Heavy Y6 error "ERROR_SUBSYSTEM_EKF_PRIMARY" on rc7
@wifiguru10 wrote: Running 3.4-rc7 on my Y6. Everything flies great, stable, a little drift in pos-hold. Not rock solid, but not bad. I'm getting errors 24-0 and 24-1 on the logs near the end of the...
View ArticleGeofence uploading "not supported" with missionplanner 1.3.41
@roland95 wrote: Hi! I cannot upload geofence to APM2.8 with missionplanner Version 1.3.41; The message at the screen is "Not supported". Previous version of missionplanner 1.3.39 worked very well;My...
View ArticleDataFlash logs don't show CMD altitude?
@Mike_Jones wrote: I am trying to graph the the CMD altitude vs the actual altitude. However, the CMD doesn't match the actual. I am plotting GPS ALT vs CMD ALT. Am I missing something or shouldn't...
View ArticleClik here to view.
Trikopter support channel selection on Pixracer
@ZaaaM wrote: Hi there i have ha smal trikopter a quantum trifecta and want to get it fly.but the majer problem is that the servo need to put on chanel 7 but the pixracer has only 6 so where do i put...
View ArticleMissing "DO_LAND_START" Command
@IronDOme wrote: Hi All I recently update pixhawk to V 1.3.41 and it has been working quite well only until few days ago when I found out that trying to add "DO_LAND_START" command was not possible as...
View ArticleEKF 2 Error - Possible bug found in EKF 2 - AC3.4 rc 6
@Andrea25 wrote: I was testing AC3.4-rc6.It seems that EKF 2 lead my copter to land itself. The only thing I know is that the copter start to drift a bit in PosHold, and then Mission Planner tell me...
View ArticleFailing to load map
@paulkumz wrote: lam running the command sim_vehicle.py --console --map --aircraft test and after that run wp load ../Tools/autotest/ArduPlane-Missions/CMAC-toff-loop.txt but after all this Xterm just...
View ArticlePPM with Pixracer
@dkemxr wrote: I'm not sure if this is an Arducopter issue or a hardware issue but specific issues with Pixracer have been adressed in Arducopter so I'll ask. PPM input does not work. In my case its...
View Article$ for build/compile instructions
@maxmay wrote: I invested time to build/compile Copter 3.3 for Pixhawk , now I want to invest $ for your copter 3.4 build instructions ! please help ! Posts: 4 Participants: 3 Read full topic
View ArticleRC7 LeddarOne Rangefinder system fail
@Lance_B wrote: First I guess I should ask if this device has truly been added to the firmware - if not disregard. If it is:Upon testing mine, (set Serial1_Protocol = 9 - Lidar, and Rngfnd_Type = 12,...
View ArticleClik here to view.
Pixracer with RC Helicopter
@zhangsir wrote: @tridge@Rob_Lefebvre understand Pixracer only 1-6 output channel, then, RC helicopter ESC to access 8-channel, how to set it? DSC04948.jpg3200x2133 628 KB Posts: 1 Participants: 1...
View ArticleGPS configuration RC7
@Gregmaan wrote: Hi I am testing with RC7 and get weird messages about the gps configuration:Sometimes the baud rate is 115200 mostly 38400 from messages?Is there a way to get allways the same...
View ArticleLIDAR on Quadplane
@Detleff wrote: Hi there, Is it possible to use LIDAR during VTOL_LAND? If yes, does it also work when Q_RTL_MODE parameter is set to 1? Finally, is there a SITL Octo-quad model available? Detleff....
View ArticleClik here to view.
Arduplane Missions with consistent offset to the right of waypoint path
@Pedro_Alves wrote: Hey, I just started with Aurduplane by now (flying Ardupilot based multicopters since 2013) and I'm trying to tune my Auto missions without success. The plane follows the waypoint...
View ArticleCopter spin in LOITER mode (3.4-rc2)
@jyl58 wrote: Hi All : In LOITER mode ,after copter takeoff ,the vehicle start spin,and the yaw stick dos't work .Anyone can help me analyze the flight log? Thanks very much . Firmware :Copter...
View ArticleMapping: too many pictures
@Basti_K wrote: I have been trying for some time unfortunately without result with my Copter to map,but more images are generated as in the log.As an example:135 camera shots and 153 pictures in the...
View ArticleProblem with mission planner and telemetry
@cookmangr wrote: I m facing a problem I m using a pixhawk with tellemetry and storm32 gimbal controllerI have connect the storm32 with pixhawk through serial4 When i have on the storm32 i cant...
View Article3.4-rc7 copter arm via mavlink even with RC turned off!
@trancept wrote: Hello, Update this morning from rc6 to rc7 and fly goes well with quad + pixhawk + px4flow + terraranger. What I saw that could be dangerous is that the copter arm via mavlink even...
View ArticleBBBmini: Second magnetometer from GPS
@steveb1475 wrote: Hi I got a ublox neo m8n gps for my bbbmini. It has an extra pair of wires that I think are for the compass. Where would you connect the second compass on the mini and how would you...
View ArticleClik here to view.
Rotated Mapping Polygons' Starting Point
@IronDOme wrote: I am unable to force starting point at the the when I have rotated mapping polygons.Please see the attached, how do I get around that? Thanks in advance Di Start Point.JPG1545x962 383...
View Article