3DR Power module not measuring current
@Nihal wrote: Hi, I'm running plane 3.5.2. Im using a 3dr power module. The voltage is calibrated correctly as given in the guide -...
View ArticleGPS_GNSS_MODE and the best configuration
@pauljatherton wrote: Just looking into this parameter trying to understand why in my 4 ardupiloted craft that they all behave differently when it comes to the responsiveness of the GPS - for which...
View ArticleSupport for 16 channels?
@wicked1 wrote: Would it be possible to support 16 PPM channels?Is anyone else interested in it?Could the extra two be passed through to unused motor ports?Even the ability to assign 1-10 to internal...
View ArticleClik here to view.
Radar and Ardupilot Flight Controller System Wins UTM Drone Sense and Avoid...
@Hongshu wrote: Last week at the Unmanned Traffic Management (UTM) Drone Sense & Avoid technology competition in Syracuse, Aerotenna took home First Prize by demonstrating the effectiveness of a...
View ArticleAirspeed and groundspeed units?
@pauljatherton wrote: Hi, in APMP2 I see airspeed and groundspeed in the Info View panel under the HUD. It shows these as type (float) - what units are these in reality? Metres/sec or kph or knotts?...
View ArticleAuto Mode problems with pixhawk on rover
@ajmarra wrote: I using pixhawk autopilot with mission planner and when I set my rover in auto mode, the vehicle immediately begins making 360 degree turns. How to fix the problem? Posts: 3...
View ArticleProblem with throttle out Copter 3.4.2
@Niels wrote: Hi everybody, not really sure if i'm doing it right. Building my third copter now and i'm standing in front of a problem i never experienced. As in the attached log i experience some...
View ArticleMotor angle and alignment. Critical?
@Keshka_Kotera wrote: I have a folding 650 class frame with 15" CF props. The tips only miss each other by about 3/4". Yes, it's a tight fit. Due to using flat low rpm motors (SunnySky X3508S-16) I am...
View ArticleSafety switch only for motors
@Kudykam wrote: Hi, Is it possible to activate safety switch to block only motors, but no AUX 1-6? So I can control my LEDs and servos without pushing safety switch? Posts: 1 Participants: 1 Read full...
View ArticleClik here to view.
RCHeli T-Rex500 ArduPilot AC3.4.2FW Maiden Flight
@zhangsir wrote: Today on my T-Rex500 helicopter, daring to test the latest version AC3.4.2 firmware. Initial feeling very good, use default parameters for basic stabilization of flight, aircraft...
View ArticleTurn off "flight path" in "Vehicle Data" screen
@Bas_Hamans wrote: Is there a possibility to turn-off the "flight path" in the "vehicle data" screen in Tower 4.0.0. I have seen there is a possibility to clear the path, but I don't want any path....
View ArticleMaiden going perfectly then sudden flip over
@autopiloton wrote: Can someone take a look at this log from the maiden flight of my new quad. Here is the setup: Holybro pixhawk 2.4.5 with V3.4.2 quadUblox NEO-M8N GPSvolo systems "the power"...
View ArticleM8n config file in wiki corrupt
@pauljatherton wrote: TheMarco M8N config file linked on this wiki page (http://ardupilot.org/copter/docs/common-ublox-gps.html) causes u-center to crash right at the end of applying the config. I...
View ArticleHow do I fly parrot disco arduplane without remote controller?
@Wieland_Beck wrote: I have been trying and trying to get this working and I can communicate with arduplane with all groundstation apps. In the setup guide it says the following: "The usual way to fly...
View ArticleClik here to view.
Technique to expand Roll and Pitch Rate PID gains without instabilities
@bnsgeyer wrote: I am writing this discussion topic illustrate how I used the filter to successfully reduce the instability to increase the P and D gains. I’ve read in the Copter traditional...
View ArticleConnecting to ArduCopter through UDP
@josealb wrote: Hello, I am trying to make a companion computer, not really a ground station but I didn't find any more appropriate sub.The first step for my project is to set the mode to guided and...
View ArticleHardly no throttle
@Cecil_Frank wrote: I have a Quantum Nova and went throw Mission Planner Wizard After all this I found the quad willnot work on motor test in Mission Planner. and works on calburating tranmitter ....
View ArticleRTL and crash after reaching home - 3.7.0?
@fireflyer451 wrote: Using APM Plane 3.7.0, I was flying a Skywalker 1800, had several flights on it with little drama. I had performed an autotune earlier in the day and all seemed good. I had tested...
View ArticleFly the Arducopter APM 2.6 autonomously
@Vikrant_Fernandes wrote: I am new to this discussion forum so please bear with me. I have a arducopter apm 2.6 flight controller. It works fine with mission planner and the fly sky RC kit. I am...
View ArticleHow to change range of offset of acc
@hamid_didari wrote: Hi guysI change the mpu6000 on my board and it seems the offset of acc is to high for acc calibration and calibration failed . i guess it becaus of soldering . how can I change...
View Article